Outer Ecb Parts

Oven is a slide in. I pulled it out just a Few inches and removed 8 screws and Pulled the face down to expose the unit. The control unit had 4 screws and 4 Plugins. It only took me less than 10 Minutes to replace unit and slide back In place. Read more

I did an internet search - found your site explaining how to fix. I purchased the upper, middle, and lower spray arms - It took about 15 minutes total. Very very easy. No more dirty dishes! Read more

The basin would fill but would not agitate, there was no sound, no grinding noises, no sound of a motor running without agitation due to a broken belt. The basin full of water was able to drain if I advanced the timer to Spin. By playing around with the timer dial further, I could get every function of the washer to operate, at least partially. So, that said electrical problem to me. I assumed the trouble was either the safety switch at the back of the lid or the timer mechanism. Tested... Read more

Turn off power to machine, Take off door panel - 12 screws. hold up door panel a bit and make sure to remove the ribbon from the touch pad to the control module (use some pliers to rock it out of the board). Since I was changing the Module, I just removed the 1 screw that held it in place and it gave me some more room to get my hands in there and remove all the wiring freeing up the board to remove the touch pad ribbon last (I didn't want to tear it because I was not replacing it and after 9... Read more

Ordered the part from Appliance Part Pros. It came in one day! Had to disconnect the gas line and wrestle the unit out of the wall cabinet, but the repair was easy and straightforward. The job took less than an hour Read more

It's very easy fix. If your unit flashing e2 f2. It's your relay board take screw if on door couple latched s on the gray relay box pull wires harness of slow. Re install the same way it came of Just remember to cut the power off first . Leave your door open when re powering unit. Read more

• Touchpad does not respond

I ORDERED A NEW CONTROLLER BOARD. THE DIRECTIONS SHOWED HOW TO UNCLIP THE OLD BOARD BUT THE FASTENERS WERE ON THE LEFT SIDE NOT THE BOTTOM AS INDICATED ON THE REPAIR INSTRUCTIONS. AFTER REASSEMBLY THE DISHWASHER FUNCTIONED AS NEW. THNKS FOR THE INSIGHT. Read more

So initial thought was bad bake igniter. I'bve replaced this before so I replaced it again and it wouldn't glow. Checked broil igniter and same thing, no glow. Checked voltage at molex connector for bake igniter and it went from 6.6v to 3.4v when triggered to glow -- well below the 120v expected. Ordered new clock/controller and overlay -- it shipped the next business day! Removed a handful of screws from the back panel to expose the clock/controller and removed/ replaced it with new... Read more

My experience could not have been smoother. I called the repair guy just to see how much money I saved and I was shocked! I saved $123.00, thanks to appliance parts pro. Thank you so very much for your professional help, great prices & super fast shipping! From now on, when another appliance needs repair I'm going to you guys first. I'm spreading the word to every single person I know and posting it on social media as well. Thanks again, Jeremy Read more

Replaced timer. Took 15 minutes Read more

I replaced the control board. Repair company wanted $395.00. I ordered the board for 140ish, 5 days later, 9 screws, 6 moduler plugs....working oven. The hardest part was pulling out the stove. Read more

Checked circuit breaker to d/w first. Good. Went to website to see no power issues. Most all of them mentioned the noise filter being the problem. Removed filter from machine and found the corner melted where fuse is located. Ordered new filter, installed, and now have power to switches. All the information I found on the website really made this a easy job to get done. Read more

• Timer will not advance

Just as the folks in the comments section said, I tested everything to make sure the timer had power which it did. I then tested with the OHM tester and saw that the switch was open when the timer was set to any drying cycle. So i changed the timer and voila! timer is functioning again. It was a very easy fix. Just pop the four screws out of the back of my timer panel on the dryer, detach all the wires, lift up on the little bracket that is holding the timer in place and twist it, and it... Read more

After unplugging the washer from the electrical outlet, the top of the washer was removed without a problem in order to allow easy access to the Central Control Unit (CCU) at the top of the back end of the washer. A cell phone was used to photograph the wiring layout and connectors plugged into the CCU, and then all connectors and the harness were carefully removed from the CCU without incident. Attempting to remove the old CCU, the plastic retaining clips built into the old CCU housing broke... Read more

Bought the circuit board you recommended and it fixed it perfectly Read more