Power Small Engine Regular Starter Parts

This moisture sensor monitors dampness inside the dryer drum and signals the control when fabrics are dry, helping automatic cycles end on time and avoid overdrying. Replacing a failed sensor can restore consistent Auto Dry performance and cycle times. What it does:

• Detects moisture level via conductivity across the sensor surfaces inside the drum
• Sends feedback to the control so Auto Dry cycles advance and stop correctly
• Helps prevent overdrying and underdrying in sensor-based cycles
• Common symptoms of a faulty sensor may include: auto cycles ending too soon or running too long, clothes remaining damp, or the dryer staying on "Sensing" while timed cycles still work

• 1 moisture sensor

• Disconnect power and, if applicable, shut off gas before servicing
• Access the sensor at the front bulkhead/lint housing area; remove front panel as needed per model
• Transfer connectors and route wiring exactly as original; secure the sensor firmly
• Clean the sensor contact surfaces with rubbing alcohol; residue from dryer sheets or fabric softeners can affect readings

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.

If your dryer is overheating, running too hot, or taking extended times to dry clothes, a faulty cycling thermostat is often the cause. Easy DIY fix.

The Dryer Guide Sensor Assembly is designed to ensure precise drying cycles in your Samsung dryer. This genuine OEM part guarantees compatibility and reliable performance, maintaining your dryer's efficiency. Featuring a high-quality assembly, it accurately monitors moisture levels, helping to prevent over-drying and reduce energy consumption. Installing the Dryer Guide Sensor Assembly enhances the lifespan of your appliance by ensuring optimal operation. Whether you're replacing a worn-out sensor or repairing your dryer, this component provides a seamless fit and easy installation. Trust in the Dryer Guide Sensor Assembly to deliver consistent drying results, improving your overall laundry experience. Compatible with a range of Samsung dryer models, this genuine OEM part is the perfect solution for maintaining your appliance's functionality and performance.

Dryer not heating or overheating? This thermostat regulates temperature during the drying cycle. Common DIY repair that restores proper heat control.

Fix a dryer that won't heat or overheats with this cycling thermostat. Regulates heating element temperature for consistent drying. Simple DIY repair.

The Electrode is an OEM replacement part for Whirlpool dryers. It is responsible for detecting the moisture levels in your laundry during the drying cycle, allowing the dryer to automatically adjust the drying time and temperature. It helps prevent over-drying or under-drying of your clothes, saving energy and protecting them from potential damage.

A bad electrode can occur due to wear and tear, damage, or a buildup of debris or lint. If you notice symptoms such as clothes taking longer to dry, the dryer shutting off prematurely, or inconsistent drying results, it may be time to replace the moisture sensor bar electrode.

Symptoms of a bad electrode include:

• Clothes taking longer to dry than usual
• The dryer shutting off prematurely
• Inconsistent drying results, with some items remaining damp

Repair your dryer by replacing the faulty or damaged electrode with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Dryer won't start but lights work? A faulty door switch prevents operation. This replacement switch restores normal function in under 10 minutes.

Dryer won't heat or overheating? The temperature switch controls heat settings. DIY-friendly repair—just swap wires and reassemble. Takes 20 minutes.

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

This replacement door switch restores proper door sensing in your refrigerator. It detects when the fresh food or freezer door opens and closes, turning interior lights on/off and signaling the control so door-ajar alerts and related features work correctly. What it does:

• Senses door position to control interior lighting
• Sends door status to the control in many models for features like door-ajar alerts or fan pause
• Helps prevent overheating near the light by ensuring it turns off when the door is closed
• Common symptoms of failure: no interior light, light stays on, flickering light, or persistent door-ajar alarm

• 1 door switch

• Disconnect power to the refrigerator before servicing
• Carefully release the old switch from the cabinet opening and unplug the wire harness
• Connect the harness to the new switch, orient correctly, and snap or seat it fully in the opening
• Restore power and verify proper light operation and door-ajar indication

If your dryer takes too long to dry or overheats, the cycling thermostat may have failed. This part regulates heat by cycling on and off. Easy DIY fix.

This internal-bias thermostat controls exhaust temperature in your dryer, cycling the heat on and off to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent drying performance and help protect the dryer from overheating shutdowns.

• Monitors exhaust air temperature and opens/closes the heating circuit to regulate heat
• Provides the bias function used by automatic cycles for correct temperature control
• Failure symptoms can include no heat or low heat, long dry times, overheating or high-limit trips, and inconsistent cycling temperatures
• Helps prevent thermal cutoffs caused by restricted airflow or faulty temperature regulation

• Disconnect power before servicing; for gas models, also shut off the gas supply
• Access location is typically on the blower/exhaust housing; note wire positions and transfer one at a time
• Ensure the thermostat mounts flush for proper sensing; tighten screws securely
• After replacement, verify good airflow and clear venting to prevent repeat failures

Fix a refrigerator that won't cool or clicks but won't start. This compressor start relay and overload protects against overheating. DIY repair in 30 minutes.

Dryer won't start or overheats? A faulty high-limit thermostat breaks the heating circuit to prevent damage. Easy 5-10 minute DIY replacement fix.