Range/Range/Oven Surface Element Board Parts

Fridge keept building up ice in defrost drain drain in freezer. Once the drain pan filled with ice it drips into fridge compartment. After taking things apart three times to thaw it out, decided to replace defrost components - heater and temperature switch. In addition to new parts, also added a 12 gauge copper wire hook that hangs from defrost heater into the defrost drain. After this, the defrost cycle is running as expected, but will not know if the issue is corrected until a year or so... Read more

I tested the fan outside of the freezer with an adapted direct plug-in cord and it ran fine. I tested the controller tsd it was within the good range along with the run capacitor and it tested good as well. I then tested the compressor resistance, it tested good, although the compressor could have been mechanically bad, it wasn't and I don't know of a way to test for it. I found a youtube video and tested the defrost control which seemed to be bad. Then I tested the control-temperature... Read more

We simply removed the back panel off the stove, removed four screws and unplugged the controller. It was so quick and easy. It took about five minutes to replace. Read more

Replaced the user interface panel. Four screws and 3 idiot proof wired connections. Hardest part was pulling the fridge out from the wall to unplug it before the swapping part. Read more

We purchased the electronic control board (for 1/2 of what the technician wanted for the part), opened up the door to the dishwasher, took out the old board and put in the new one. It was a 15 minute repair and we saved almost $300 doing it ourselves! (Thanks to AppliancePartsPros.com and YouTube!) Read more

Googled what would cause that. Found or needed a new timer. Searched for the best priced timer online. Found one here for a good price. Replaced it myself very easy replacement and saved at least 100 dollars doing it myself. Read more

I ordered a timer from Appliance Parts Pro, I watched the video on how to install it, I installed the timer and it works fantastic! I am now so glad that I can be busy and hear the buzzer go off to let me know that the clothes are now dry. Thank you so much Appliance Parts Pro! Read more

I replaced the Timer knob components. Removing the cover that contains the Timer was simpler than I anticipated. Just remove the screws on the top of the back of the machine. Hold the cover and lift up and push to the left (facing the front of the washer). Removed the Timer Knob Clip with small needle-nose pliers. Grasped the Timer and turned counterclockwise to remove and unplugged the wiring clip. The timer is seated to the cover and held securely in place with one screw. I seated the new... Read more

Searched the web and determined it was something called a noise filter. Ordered the part from ApplianceParts Pros. Received it in about 3 days, normal shipping. Replaced the part. Took about 15 minutes from start to finish. Problem solved. Cost less than $50. Read more

Took out the old part and replaced it with the new part. Now all is working. Thank you so much. Read more

1st. replaced thermostat probe inside wall oven - no change. Then removed range heating element and measured it with ohm meter for continuity and found it to be OPEN. Ordered replacement range heating element; measured it before install and found it to be a few ohms - installed in less than 5 minutes and tested. ALL WORKS GREAT. Both items purchased with shipping were just over $100. (I chose to keep the thermostat probe instead of returning it being the oven is just over 10 years old). Read more

• Not drying dishes properly

Turned off power to dishwasher. Removed front bottom cover of dishwasher and removed the wires going to each end of the heating element. unscrewed the two nuts holding the faulty heating element in place. Then removed bottmo dish rack and spinning washer arm from inside the dishwasher. Removed old heating element and replaced with new one. Installed in reverse order (tightened two nuts, connected wires, etc.). Turned power on as last step and was off and running...or should I say washing. Read more

Based on symptoms it looked like the timer was not working. I did a web search to confirm this and found your web site. Entering the model number of the washer (Whirlpool) I found the timer and related information. This confirmed my diagnosis. I also looked at the video on how to change the timer. This was invaluable! The video saved me hours and probably a washing machine. I ordered the timer, it arrived as promised, I installed it per directions and the machine works... the video makes... Read more

Replaced user interface reinstalled front cover and added in affresh and ran a cycle. Works like a dream now! Read more

• Element will not heat

This repair was on a GE glass Cooktop range. This range has two indicator lights, a Burner On light, and a Hot Cooktop Light. The problem I was having was, the Hot Cooktop stayed on all the time (24x7), even when the cooktop surface had been off for hours and was cold. YouTubes that I viewed were all misleading on this symptom. They all pointed to the switch, which is the fix for the Burner Light staying on, not the Hot Cooktop Light staying on. I figured it out by going to the schematic.... Read more

Flipping the breaker worked 5x until it just died totally. New UI board brought it back to life. Read more