Circuit Board Parts

This middle spray arm hub secures the dishwasher's middle spray arm to the feed tube and lets it spin smoothly, helping deliver even spray coverage so dishes in the upper rack area get properly cleaned.

• Connects the middle spray arm to the water feed/manifold and serves as its rotating center
• Keeps the arm aligned so jets can distribute water evenly
• Wear or cracks can cause the arm to wobble, fall off, bind, or stop spinning
• Symptoms include poor cleaning on the upper rack and unusual noise from the arm area

• Disconnect power and water supply before servicing
• Remove the middle spray arm per your model's design and note its orientation
• Transfer and reuse any original screws, clips, or washers; install the new hub without overtightening
• Spin the arm by hand to ensure free movement before running a brief test cycle

The defrost timer governs the automatic defrost cycle, periodically switching the refrigerator from cooling to defrost. Replacing a failed timer restores reliable defrosting to limit frost buildup and help maintain steady, consistent temperatures. What it does:

• Advances the system through run and defrost periods at set intervals
• Sends power to the defrost heater during defrost, then returns the unit to cooling
• A failed timer may cause heavy frost on the evaporator, poor cooling, or continuous running
• A timer that does not advance or is stuck can leave the refrigerator in defrost or prevent defrost entirely

• 1 defrost timer

• Disconnect power before servicing
• Access location varies by model
• Photograph wire positions; move wires one at a time to the matching terminals on the new timer
• Transfer any mounting bracket, secure the timer, and restore power to verify operation

This electronic control board governs your dryer's cycle logic and responses. Replacing a failing board restores proper communication between the controls and internal components to help resolve dead console, no-start, or erratic cycle behavior.

• Interprets cycle selections and sensor inputs to run the programmed operations
• Sends control signals to the dryer's components as designed by the model
• Coordinates timing and status indicators
• Common symptoms: won't start, console unresponsive, cycles that won't run/advance/end properly, intermittent power or random lights/beeps

• Disconnect power before servicing; this board carries line voltage.
• Use ESD precautions and handle the PCB by the edges.
• Photograph/label connectors and move wires one at a time to the new board; secure with existing bracket.
• After installation, run the model's diagnostic or test routine if applicable.

The Electronic Control Board is an OEM part for Whirlpool ranges. This control board manages and regulates the range’s functions, including temperature settings, timer operations, and control of the oven's heating elements. 

Causes of a bad electronic control board include electrical surges, overheating, and aging components.

Symptoms of a bad Electronic Control Board include:

• The range not heating properly
• Error codes displayed on the control panel
• Unresponsive or erratic buttons and controls
• Inability to set or maintain temperatures accurately

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This factory fixing kit supplies the OEM hardware required to secure the appliance or designated components during installation or service. Replacing missing or damaged fasteners restores a solid, aligned mount so the unit stays stable without shifting, rattling, or gaps.

• Provides the correct hardware to fasten parts per your model's installation or service instructions
• Replaces stripped, corroded, or missing screws/clips that lead to looseness
• Helps maintain alignment and clearances to prevent gaps, rattles, or vibration
• Typical symptoms: loose mounting, panels that shift, or movement when opening/closing doors or drawers

• Disconnect power; shut off water or gas if applicable before starting work
• Follow the model-specific installation/service manual for attachment points and sequence; use the proper driver bit and do not overtighten
• Verify the unit is level and securely anchored; check clearances and operation after securing

The Frigidaire Range Control is an OEM component specifically designed for Frigidaire ranges. Located on the control panel, the range control houses all interactive buttons and knobs to operate the cooktop burners and oven. 

Causes of failure include damage from excess moisture, cracks developing from repeated tightening/loosening of knobs, or wear of electronic switches impacting responses.

Symptoms of a bad range control include:

• Unresponsive or inaccurate oven/stovetop controls  
• Inability to power on or adjust temperatures
• Faulty burners failing to ignite or flame improperly
• Loose, damaged, or missing knobs hindering the use

This OEM component is also compatible with Crosley, RV, and some Kenmore-branded ranges and ensures a straightforward repair experience.

This power board assembly manages and distributes electrical power within the appliance's control and heating circuits. Replacing a failed board can restore consistent power, responsive controls, and reliable heating when the unit won't turn on or behaves erratically.

• Routes incoming power to the appliance's control and load circuits
• Works with the control system to switch relays and energize components as commanded
• Supports reliable operation of powered components during cooking cycles
• Failure signs include: unit won't power up, no heat, dead/unresponsive display, or intermittent shutdowns

• Disconnect power at the breaker or unplug before servicing
• Electronics are static-sensitive—use ESD protection and handle the board by the edges
• Photograph/label all wiring; transfer connectors to the new board one at a time
• Ensure all connectors are fully seated and mounting hardware is secure before restoring power

This electronic control module generates and manages ignition spark for DSI-equipped gas ovens/ranges. Replacing a failed unit restores reliable burner lighting and can resolve issues such as no spark, repeated clicking, or the oven/broiler not igniting.

• Generates high-voltage pulses to ignite gas at the DSI electrodes
• Times and controls ignition cycles; energizes the gas valve only during commanded ignition
• Monitors flame presence through the sense circuit and may retry or lock out if ignition fails
• Common symptoms of failure: oven or broiler won't ignite/heat, no clicking/spark, intermittent ignition, or continuous clicking
• Intended for models that use direct-spark (DSI) ignition systems, not glow-bar/hot-surface igniters

• Disconnect power and shut off gas supply before servicing
• Handle the control as an electrostatic-sensitive device; avoid touching terminals
• Transfer wires one at a time and mount the module securely with a proper ground
• After reassembly, restore utilities and verify normal ignition operation

This clock timer is the range/oven's electronic control that runs bake and broil and keeps time. Replacing a failed unit restores the display and keypad response so the oven can start and operate correctly.

• Controls oven heating by switching relays for bake and broil
• Provides clock and timer functions on the front display
• Receives keypad inputs to set temperatures, times, and cooking modes
• Typical failure symptoms: blank or dim display, unresponsive buttons, oven won't start or heat, intermittent beeping or error codes

• Disconnect power at the breaker before servicing
• Note/photograph wire locations; move connectors to the new control one at a time
• Handle the board by the edges and use anti-static precautions
• Transfer any model-specific brackets or faceplate/overlay as required and set the clock after installation

This electronic control board is the appliance's central controller, coordinating power to key components so cycles start, run, and finish correctly. Replacing a failed board restores reliable, automatic operation and resolves control-related faults. What it does:

• Orchestrates timing and power to major loads (motors, valves, heaters, pumps)
• Failure may present as no start, won't complete cycle, intermittent operation, or unresponsive/erratic controls
• Can prevent individual components from running even when they test good
• Susceptible to damage from power surges, overheating, or moisture intrusion

• 1 electronic control board

• Disconnect power at the breaker before servicing; verify power is off
• Use ESD protection and handle the board by the edges only
• Access the control compartment, photograph wiring, and move connectors one at a time to matching terminals
• After installation, run a diagnostic/test cycle per your tech sheet

The Cntrl-Elec is an OEM component specifically designed for Whirlpool dishwashers. This control board governs and directs the electronic operations of the dishwasher. It allows the dishwasher to run through wash cycles and heat water to the appropriate temperatures. 

Symptoms of a bad control board include:

• The dishwasher not turning on at all
• The dishwasher not completing full cycles
• Issues with heating or not heating water properly
• Error codes appear continuously 

The control board is susceptible to faults over several years of regular usage. Water exposure or power surges can potentially damage electronic components. Replace yours with this genuine Whirlpool OEM part to restore full functionality to your dishwasher.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This mechanical defrost timer automatically switches the refrigerator between cooling and defrost cycles. Replacing a failing timer helps clear evaporator frost so temperatures remain stable and cooling performance is consistent. What it does:

• Initiates the defrost cycle at regular intervals and then returns the system to cooling
• Interrupts compressor power and energizes the defrost heater during defrost
• Helps prevent heavy frost buildup on the evaporator
• Common failure symptoms include thick frost on the evaporator/back wall, warming in the fresh food section, the unit running constantly or getting stuck in defrost, or repeated clicking from the control area

• 1 defrost timer

• Disconnect power before servicing; components in the defrost circuit can be live and hot
• Access locations vary by model
• Note or photograph wire positions; transfer wires one at a time to the new timer
• Secure the timer in the original bracket/orientation and reassemble before restoring power

This dryer timer controls and advances the cycle you select, routing power to the correct components and shutting the dryer off at the proper time. Replacing a worn timer restores consistent cycle timing and end-of-cycle shutoff.

• Controls cycle selection and duration
• Advances the dial through the program and turns the dryer off at the end
• Routes power to dryer components at the correct times during the cycle
• Signs of a failing timer may include: cycle not advancing, running indefinitely, stopping early, or erratic timing

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the control knob and access the console to unmount the old timer
• Label or photograph wiring; move terminals to the new timer one at a time to avoid miswiring
• Align the timer shaft with the dial, secure the timer, and test operation before reassembly

This control board is responsible for controlling the main electronic functions of the refrigerator. It monitors and manages the temperature and cooling settings of the appliance. Models that are compatible with this part can have the temperature adjusted digitally. If a control board is damaged or faulty, the set temperature of the appliance will not match the actual temperature reading the machine is putting out.To install this control board, open the refrigerator door, and make a note of the small white box on the ceiling area of the refrigerator. Remove the four screws holding this box in place. The control board is contained in the box and can be removed by popping the clip. Unplug the old board from the wiring harness and install the new one.This Whirlpool refrigerator control board is a genuine OEM part and is sourced directly from the manufacturer. It is compatible with Whirlpool, Maytag, Kenmore, and Magic Chef appliances.

The Control Board is an OEM part for Whirlpool dishwashers. As the central processing unit, the control board orchestrates each cycle by coordinating motor, pump, heater and other component functions. It monitors cycle progression, temperatures and safety features.

Causes can be circuitry damage from power surges, water damage or normal component wear over time. Control boards experience constant usage with each cycle.

Symptoms of a bad control board include:

• The dishwasher not starting or powering on properly
• Inoperable or unresponsive buttons/controls
• Inability to advance through wash cycles
• Error codes displayed
• Cycle functions become intermittent

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This dryer timer is the cycle control that advances your dryer through Timed and Auto Dry settings. Replacing a failed timer restores proper cycle progression, start/stop, and end-of-cycle shutoff.

• Advances the cam and internal contacts to move the dryer through heat, motor, and cool-down steps
• Governs run time on Timed Dry and Auto Dry cycles
• Routes power to the correct circuits in sequence; a failed timer may not advance or may stop early
• Common symptoms include timer knob not moving, dryer running indefinitely, or not starting on certain settings

• Disconnect power; for gas models, also shut off gas
• Remove knob/dial, open the console, and unmount the timer
• Label or photograph wiring; transfer wires one at a time to the new timer
• Reassemble and test both a Timed Dry and an Auto Dry cycle