Module Parts

This ice enclosure is the molded housing that surrounds the icemaker inside the freezer, helping position the assembly and guide airflow for reliable ice production. Replace a cracked or missing cover to restore proper fit and protection around the icemaker.

• Mounts around the freezer icemaker to shield and correctly position the assembly
• Helps direct airflow for consistent ice formation and harvest
• Reduces frost intrusion in the icemaker area
• Common fix for cracked, warped, loose, or missing housing

• Disconnect power and turn off the water supply before service
• Remove the ice bin and icemaker as needed to access the enclosure
• Transfer any clips/brackets from the old part and reuse existing hardware
• Verify icemaker alignment and fill tube clearance before restoring power

This ice maker cover fits over the ice maker head to protect the control module and moving parts inside your freezer. Replacing a cracked or missing cover helps prevent frost intrusion and restores a clean, finished look.

• Shields the ice maker mechanism from debris and moisture
• Helps maintain airflow to reduce frost at the ice maker face
• Replaces a cracked, warped, or missing cover with broken tabs
• Can help address exposed gears/wiring or rattling from a loose cover

• Disconnect power to the refrigerator before servicing
• Remove the ice bin to access the front of the ice maker
• Release retaining tabs or screws and remove the old cover
• Align and snap the new cover fully into place; verify it's secure and clear of moving parts

Made by Bosch. Common program control module for Bosch dishwashers SHU53/68. NOTE The manufacturer has redesigned the cover and indicator lights. Lights may be covered by the plastic case. You may have to remove the square covers over the indicator lights if needed. The same case is used for 6 and 8 indicator light models. They also no longer use the red bulb indicator lights, small surface mounted lights are used instead. If you require the Jumper Wire that goes with certain models, the part number is 00167782.

An ice auger rotates inside the freezer's ice bin to move cubes to the crusher and out the dispenser chute. Replacing a worn or broken auger restores consistent dispensing and helps eliminate jams and grinding from a slipping spiral.

• Advances ice through the bin toward the crusher/dispenser chute
• Works with the crusher assembly to deliver cubed or crushed ice based on the selector
• A stripped or cracked auger may result in little/no ice dispensing while the motor runs
• Damage can cause ice jams, uneven dispensing, or grinding noises from the bin

• Unplug the refrigerator; remove and empty the ice bin, allowing any frost to thaw
• Wear cut-resistant gloves—crusher blades and sheet-metal edges are sharp
• Disassemble the crusher/blade stack and note the exact blade/spacer order
• Transfer the blade stack, bushings, and hardware to the new auger; reassemble and confirm smooth rotation before reinstalling

This OEM replacement part is an ice container for refrigerators. The ice container is the plastic bucket that holds the ice that is made by the icemaker. Over time, an ice container can become damaged due to excessive wear and tear. If the ice container is cracked or broken to the point where it can no longer hold ice, it will need to be replaced.To replace the ice container, start by unplugging the refrigerator. Once unplugged, proceed to open the freezer door. Locate the two mounting screws that attach the ice container to the icemaker. Once found, proceed to unthread the screws to remove the old container. After pulling the old container out, slide the new one in place and fasten the mounting screws that secure it to the icemaker. This genuine replacement part is sourced directly from the manufacturer and is sold individually. It is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand refrigerators.

The electronic control board is the appliance's main control module. It interprets inputs from the user interface and sensors, then powers and times key components to run each cycle. Replacing a failed board restores reliable, predictable operation.

• Coordinates cycle sequencing and powers components through onboard relays
• Receives signals from switches/sensors and manages overall operation
• Common failure symptoms: unresponsive controls or no power
• Won't start, stops mid-cycle, or won't advance through a cycle
• Intermittent operation, flashing lights, or fault/error codes tied to the main control

• Disconnect power at the breaker before servicing; verify the unit is de-energized
• Use ESD protection; handle the board by the edges to avoid static damage
• Photograph/label wiring and move connectors one at a time to the matching terminals
• After installation, run the appliance's diagnostic/test cycle to confirm proper operation

This automatic ice maker assembly forms and releases ice cubes into your refrigerator's bin, restoring steady ice production when the original unit fails. Install to resolve no-ice or incomplete harvest issues and keep ice ready when you need it.

• Freezes water in its mold and ejects cubes into the storage bin during each cycle
• Pauses production when the bin is full to prevent overflow
• Coordinates with the refrigerator control and water valve for proper fill and harvest timing
• Common symptoms include: no ice production, won't cycle/harvest, cubes jammed, or leaking/overfilling near the ice maker

• Disconnect power and turn off the water supply before servicing
• Remove the ice bin; unmount the old ice maker and unplug its connector; mount and connect the new assembly
• Align the fill tube with the ice maker's fill cup to prevent leaks
• Restore power and water; allow several hours (up to 24) for normal ice production to resume

The Icemaker is an OEM replacement part for Whirlpool bottom-mount and side-by-side refrigerators. 

Causes of a bad icemaker can include failures in electronic controls, cold plate freezing, or mechanical components that inhibit harvest functions.

Symptoms include: 

• Failure to produce ice or reduced ice output
• Jammed or broken ice delivery mechanism  
• Dripping or leaks from the icemaker system
• Error codes appearing on control panels

This OEM Whirlpool replacement icemaker is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Electronic Control is an OEM part for Whirlpool dishwashers. It is the main circuit board that regulates all electrical functions and directs components during cycles. Sensors throughout the dishwasher relay information to the control board, which processes data and generates output signals to control mechanisms such as wash motor, heater and dispensers.

Causes of a bad electronic control include failures from long-term, continuous usage overload, issues due to power fluctuations or surges that disrupt circuitry.

Symptoms of a bad electronic control include: 

• Fault codes displayed 
• Lights, buttons or other functions malfunctioning
• Inability to start cycles or advance through phases
• Irregular cycle times, temps or abnormal sounds  

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and Kenmore models. 

This ice storage bin holds the ice made by your refrigerator's icemaker and keeps it contained and easy to access in the freezer. Replace a cracked or warped bin to prevent spills, jams, and poor seating.

• Collects and stores ice cubes produced by the icemaker
• Keeps cubes contained to minimize spills and stray frost
• Slides/seats on the designated rails or shelf area in the freezer
• Common signs of failure: cracks, broken tabs, bin won't seat or slides out, ice falling into the freezer

• Unplug the refrigerator or disconnect power; switch the icemaker off
• Pull the old bin straight out; empty and clean the area
• Slide the new bin in until fully seated; restore power and turn the icemaker back on

This electronic control board kit is the appliance's central controller, coordinating inputs and powering key components. Replacing a failed board restores proper operation, responsive controls, and reliable cycle management. What it does:

• Manages timing and power to motors, valves, heaters, fans, and other loads
• Interprets sensor and user-interface signals to start, run, and end cycles correctly
• Common failure signs: dead or unresponsive controls, cycles that won't start/finish, repeated error codes, or intermittent operation
• Helps address issues caused by power surges or board damage

• 1 electronic control board (module)

• Disconnect electrical power to the appliance; turn off gas/water if applicable
• Use ESD protection and handle the board by its edges
• Photograph wiring; transfer connectors one at a time and match any jumpers/DIP-switch settings from the original board
• Restore power and perform any model-specific tests or programming per OEM instructions

This radiant cartridge is the plug-in cooking surface used on Designer Line modular cooktops. It restores a smooth black surface and consistent, even heat when the original cartridge is damaged or no longer heating properly.

• Provides radiant heat beneath a smooth glass surface for everyday cooking tasks
• Self-contained plug-in module that seats in the cooktop bay and delivers heat to cookware
• Common symptoms prompting replacement: no heat, uneven or intermittent heat, or visible cracks/discoloration on the surface
• Restores normal heating performance when matched to a compatible modular cooktop

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Lift out and unplug the old cartridge straight up; avoid prying on the glass surface
• Inspect and clean the receptacle; align and firmly seat the new cartridge until fully engaged
• Restore power and test heating at low and high settings using appropriate cookware

The Dishwasher Electronic Control Board is essential for managing the various functions of your dishwasher efficiently. This genuine OEM part ensures reliable performance and seamless integration with your Samsung dishwasher. Designed to handle multiple cycles and settings, it helps maintain optimal cleaning results every time. The Electronic Control Board features durable components that contribute to the longevity of your appliance, reducing the need for frequent repairs. Its precise engineering allows for easy installation, making it a convenient solution for restoring your dishwasherGÇÖs functionality. Compatible with a range of Samsung dishwasher models, this genuine OEM part guarantees a perfect fit and dependable operation. By choosing the Dishwasher Electronic Control Board , you enhance your applianceGÇÖs reliability and ensure it continues to perform at its best, providing you with the quality and efficiency you expect from Samsung.

This electronic control board is the appliance's central command module, directing power and timing so functions run correctly. Replacing a failed board helps restore normal operation when the unit is unresponsive or behaves erratically.

• Manages power and timing to components based on selected settings
• Interprets inputs from sensors/switches to control each step of the cycle
• Common symptoms: won't power on or start, unresponsive controls, random stopping, error codes/alarms

• Disconnect power before service; use ESD protection and handle the board by its edges
• Photograph wire/harness connections and transfer connectors one at a time
• Inspect and correct any shorted components or damaged wiring before powering up the new board
• After installation, follow the unit's tech sheet for any required tests, calibration, or programming steps

This dishwasher timer controls the timing and sequence of wash, rinse, drain, and dry operations. Replacing a failed timer ensures the machine advances through each stage properly for complete cycles and reliable cleaning results.

• Advances the cycle and routes power to pumps, valves, and heater at the correct times
• Can cause cycles to run unusually long/short or skip steps when failing
• Intermittent start/stop behavior during a cycle can also indicate a worn timer

• Disconnect power at the breaker before servicing
• Access the control console; document wire locations and transfer one lead at a time to the new timer
• Mount securely and route wires clear of sharp edges or moving parts
• Restore power and run a short test cycle to proper advancement

This is a Whirlpool control board intended for use with dishwashers.The control board is a critical component of the dishwasher as it controls the cycles and functions, including the draining and drying cycles. Control boards are subject to wear and tear that can render them ineffective and require them to be replaced prior to the standard lifecycle of the appliance. Unplug the dishwasher from both the power and water sources before attempting to replace the control board to prevent serious electrocution injuries. Work gloves should also be worn.This OEM control board has been sourced from the manufacturer and is compatible with dishwashers from Whirlpool, Maytag, Kitchenaid, Magic Chef, Admiral, Norge, and other brands. This part has been made from high-quality, durable, non-corrosive materials and is only sold individually.