Power Strike Small Engine Start Switch Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10312185
Burner stuck on high heat or won't regulate temperature? This infinite switch restores precise control. Straightforward DIY repair with a screwdriver.
Do-It-Yourself Stories from Customers like You
Bad oven knob sensor was causing circuit breaker to trip Kelly V. • Rockaway , NJ • December 27, 2019
Replacing the oven knob sensor was easy. Figuring out it was the sensor causing the circuit breaker to trip was the challenge.
Read more
More
Genuine Samsung part
By: Samsung
Part Number: DC64-00519D
Washer won't start or shows door lock error? This door lock switch keeps the door secured during wash cycles. DIY repair in 15-20 minutes with video.
Do-It-Yourself Stories from Customers like You
Part holding door shut broke. Richard B. • Schwenksville , PA • April 04, 2014
First I took off the spring loaded wire ring holding down the seal to the door with needle nose pliers. Pulled back the seal. Removed the 3 screws holding the part on the front of the washing machine. Slid the piece out. Took the protector guard off the off piece and unplug the wires. Put the wires into new part. Put the protector on the new part. Slid the part back into place. Screwed it back in. Put the seal back on. Put the wire spring loaded ring back around the seal. Total time 15 minutes...
Read more
More
Genuine Ge part
By: Ge
Part Number: WB24T10063
Fix a burner stuck on high or not heating with this infinite control switch. Common cause when burners won't adjust temperature. DIY repair in 20 minutes.
Do-It-Yourself Stories from Customers like You
Burner only worked on high setting Alejandro G. • East Meadow , NY • February 15, 2016
Ordered recommended part for GE appliance. Change was very simple. Followed instructions on video and removed one wire at a time. Very easy to change 5 to 10 minutes.
Read more
More
Genuine Speed Queen part
By: Speed Queen
Part Number: D504515
Dryer not heating or not getting hot enough? The cycling thermostat regulates temperature during the drying cycle. Moderate DIY repair for most users.
Do-It-Yourself Stories from Customers like You
Dryer problem no heat Judith T. • Suffield , CT • May 19, 2025
Replaced thermostat.
Read more
More
Genuine Ge part
By: Ge
Part Number: WE4M255
Fix a dryer timer that won't advance or automatic cycles that stopped working. This timer resistor regulates cycle duration. Easy 15-minute repair.
Do-It-Yourself Stories from Customers like You
Dryer would not shut off at end of any cycle Jeffrey S. • Davis , CA • January 15, 2018
I Replaced the power resistor. The old resistor had a small burnt spot and tested infinity for resistance.The terminals were too small so I had to make new connector. Any 5000 ohm ceramic filled resistor would have worked also.
Read more
More
Genuine Ge part
By: Ge
Part Number: WE4X448
The Flame Sensor is an OEM part for GE dryers. This part detects the presence of a flame in gas dryers, ensuring that the gas ignites properly for safe and efficient drying.
Causes of a bad flame sensor can include regular wear and tear, carbon buildup from the gas flame, or electrical malfunctions.
Symptoms of a bad flame sensor include:
- The dryer not heating or taking longer to dry clothes
- The dryer shutting off unexpectedly during a cycle
- The igniter glowing but not igniting the gas
- Error codes related to heating or ignition issues
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Dryer heating for only a short time then no heat at all David N. • Fairfax , CA • December 08, 2018
GE Gas Dryer Model DBVH512GF1WW began to heat for only a short amount of time so drying clothes took WAY too long. Read online that the first thing to replace are the solenoids. Bought the two solenoids from AppliancePartsPros.com for about $50 total, and it seems to have fixed the problem. Had to watch a few videos to learn to disassemble the dryer, and the job took a couple of hours, but now that I know what I'm doing it could be done in less than 30 minutes.
Also, the old solenoids tested...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 700855K
Fix burners that won't turn on or heat up with this burner switch kit. Includes mounting hardware and instructions. Easy 30-minute DIY repair.
This part fixes the following symptoms
-
Won't start
-
Element will not heat
See more...
Do-It-Yourself Stories from Customers like You
The burner switches were not controlling the burners correctly specifically the lo temps were too high the switch knobs were also worn Frank C. • Sunset Beach , NC • December 24, 2019
1) I installed 4 ea new Whirlpool 700855K switches. (The old switches had INF-240P-871 stamped on them. 700855K was the cross-referenced P/N.)
The installation was easy. There is slight difference in the terminal arrangement: 1) the old switch has raised terminals whereas the new switch has recessed terminals (for safety), and 2) the terminal markings are slightly different: The old switch has L1/L2/P/H1/H2 (5 terminals). The new switch has L1/L2/P/HC/H1(Also five terminals. I saw where one...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W10339251
Fix a washer that overfills, won't fill to the right level, or floods. This water level pressure switch monitors tub water. DIY install in 1 hour.
Do-It-Yourself Stories from Customers like You
Water level control wouldn't work Micheal W. • Millville , UT • April 11, 2014
I replaced it and the new one fit perfectly. reassembled and fired it up. Worked as desired, like new...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3399849
Dryer won't heat or start? A blown thermal fuse is often the cause. This safety component is a simple DIY fix taking about 5-10 minutes to replace.
Do-It-Yourself Stories from Customers like You
No heat Kathy D. • Clarence , NY • April 23, 2014
Replaced Thermal Fuse
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3391912
Dryer won't heat or shuts off early? The high limit thermostat monitors temperature and cuts power when overheating occurs. DIY repair in 30 minutes.
Do-It-Yourself Stories from Customers like You
My maytag gas dryer would start and the the tumbler rotate but the igniter would not glow and flame not start .gil P. • Enumclaw , WA • March 29, 2015
The 2 sensors that sit on top of the flame tube work together. The Thrmst F should check closed, as should the Cutoff-TML, in order for power to flow to the ignitor. If the Cutoff is open, it is usually because the Thrmst-F did not open soon enough. The Thermst-F will cycle, closed to open, and repeat, however the Cutoff-HTML is a one time switch. If it opens it will not return to closed, and subsequently the ignitor will not glow.
Some professionals say that if one of these sensors fail, both...
Read more
More
Genuine Samsung part
By: Samsung
Part Number: DC34-00025E
Washer won't start or shows LO/DC error? Lid lock assembly secures the lid during cycles and signals the control board. DIY-friendly repair with video.
This part fixes the following symptoms
-
Door latch failure
-
Will not agitate
See more...
Do-It-Yourself Stories from Customers like You
Dc "spin" and lo "lid lock" error codes Matthew H. • Clarksville , TN • May 19, 2015
After watching the video it was strait forward. Just Pull the screws pop the lid swap the springs "grease them" and put it back together. I would suggest that you have a person help you mostly has a second pair of hands. The lid was over rear springs and it will save you some expletives to have the extra body. I had worn out springs and the load kept becoming unbalanced during spin cycles I just happened to coincide with the Lock mechanism failing. The motor drive for the lock stopped working....
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303207102
Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.
Do-It-Yourself Stories from Customers like You
Frigidaire dryer door would not stay closed Carolina L. • Miami , FL • September 08, 2015
My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch.
I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to...
Read more
More
Genuine Ge part
By: Ge
Part Number: WH10X10008
Washer won't start or door won't lock? This door lock motor and switch assembly fixes both issues. Moderate DIY repair requires removing screws and gasket.
Do-It-Yourself Stories from Customers like You
Wash cycle would not start faint click instead of normal door lock sound Jeff N. • Charlotte , NC • August 16, 2019
Replaced door lock. It required removing the two screws around the lock, pulling the spring hoop wire from around the door gasket, and then disconnecting the two wire terminals from the lock. Reverse with the new part.
After cracking open the old lock the failure was caused by a thin plastic tab breaking off.
I also bought the door switch since it's cheap - just in case the problem was not the lock. But the door lock was the fix.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 8193882
Dishwasher won't start or door won't stay closed? The door latch bracket secures the latch mechanism for proper door closure. 30-45 min DIY repair.
Do-It-Yourself Stories from Customers like You
Replaced door latch parts. Michelle S. • Olmsted Twp , OH • September 05, 2017
Our 7 y/o dishwasher wouldn't close and therefore we couldn't get it to run. I called several service places who charged $75-$90 diagnostic plus parts & labor, and they were not able to get here for at least a week. I knew it was going to run at least $200. Kitchenaid wanted > $400 for a 1 YEAR WARRANTY, but it would cover this service call and any more throughout the next year. Seemed a little steep given the unit is already 7 y/o. I watched a couple videos on this site and YouTube and...
Read more
More
Genuine Ge part
By: Ge
Part Number: WH01X20823
Fix a washer door that won't stay closed or latch properly with this door plunger. Resolves issues with doors opening mid-cycle or failing to lock securely.
More
Genuine Ge part
By: Ge
Part Number: WC21X20249
The Return Switch is an OEM part for GE trash compactors. This part ensures that the compacting ram returns to its starting position after each compaction cycle.
Causes of a malfunctioning return switch can vary from electrical issues, such as short circuits or worn-out connections, to mechanical problems, including physical damage from wear and tear or blockages preventing the switch's activation.
Symptoms of a faulty Return Switch include:
- The compactor ram fails to return to its original position after a compaction cycle.
- The unit does not start or operate correctly, indicating issues with the cycle initiation.
- Unusual noises or behavior from the trash compactor, suggesting that the ram is not aligning or moving as expected.
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
The trash compactor would not cycle without me holding kick plate up for whole cycle when it did get back to the top of the cycle it would only stop if i opened the door Mike D. • Pine Mountain , GA • December 15, 2014
TALKED TO YOUR REPRESENTATIVE AND WE WENT THROUGH ALL THE ON/OFF AND LIMIT SWITCHS. NARROWED IT DOWN TO TWO SWITCHS. THE ON/OFF SWITCH AND THE LIMIT SWITCH ON THE DOWN CYCLE SIDE. REPLACED ON/OFF AND DETERMINED THAT THAT WAS NOT THE ISSUE. THEN UNCOVERED LIMIT SWITCHS AND REPLACE DOWN SWITCH, FIXING THE PROBLEM
Read more
More