Bottle Support Collar Parts

Replace suspension rods. Read more

Replaced all 4 suspension dampers. Read more

My 9-year-old GE washer, in which I replaced the motor two years ago, developed an extremely loud roaring sound during the spin cycle. After reviewing stories here to pinpoint the problem, I replaced the tub bearing, mode shifter, and tub seal. I also installed a new tub nut, split washer, and belt. This repair involves taking the washer apart in order to get at the tub bearing and mode shifter, which are inconveniently located in the very center of the machine. I bagged labeled all the... Read more

Replaced suspension rods. Read more

• Shakes and moves
• Noisy
• Pumps but will not spin

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

First went through the troubleshooting guide on the website and read the various stories and watched the repair videos for replacing the springs and suspension pads. Then before ordering any parts disassembled the machine only to the point of removing the cabinet to see if there were any obvious issues. The springs appeared OK but I couldn't tell of they were fatigued or not and all were in place but the tub suspension pads were definitely worn out. I then put the machine back together and went... Read more

• Shakes and moves
• Noisy

I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the... Read more

Ordered mounting bracket but was surprised to find that the bracket model number had changed many times from the manufacter date of the microwave vent unit. Was hesitant if I was ordering the right part but I trusted the cross referencing of appliance parts pro and I got the exact bracket that I needed Read more

While this is a Whirlpool dishwasher, I have the Kenmore Elite version of it. I believe them to be identical for parts. A little background: The first symptom I had of problems was plastic bits from the ball bearing retainer strips in the slides falling out. Then ball bearings falling out. A common problem with this dishwasher. When disassembling the upper basket, some of the gray plastic pieces were very brittle and easily snapped off. So I ended up replacing all of the plastic pieces related... Read more

I identified the parts I would need online, shopped for price and delivery, and ordered what I needed. I bought the support arm mount assembly and decided to replace the spray arm and tube as well. Installation was straightforward, although it took me a couple of tries to get the spray arm mount oriented correctly because it is angled to allow the spray arm to miss the deeper glasses channel on one side of the upper rack in the dishwasher. After clipping the arm support and the tube support... Read more

• Shakes and moves

We looked online at AppliancePartsPros.com under the symptoms and found it was most likely caused by the shocks. Of course there was a repair video showing how to replace all four shocks step by step, and there was a link for purchasing the four shocks at the bottom of the video. Our repair didn't go quite as quickly as on the video because we are novices, but we were able to do the repair ourselves and, once again, saved ourselves a ton of money! Now we have a very quiet washer and dryer again... Read more

Replaced the upper rack inner rail assembly. Read more

Cleaned off the oil or grease that somehow was all over the drive belt. Installed new drive belt. Installed 2 new left (blue) and 2 new right (red) rod and spring assembly. This fixed the out of balance issue during spin cycle. Read more

Cleaned off the oil or grease that somehow was all over the drive belt. Installed new drive belt. Installed 2 new left (blue) and 2 new right (red) rod and spring assembly. This fixed the out of balance issue during spin cycle. Read more

I read through the issues related to my problems. I purchased both parts so if one was fixed then the other still needed to be fixed I would have the part. I watched both videos for replacing the parts which made things so much easier. I will say prying in the front clips was the biggest issue out of the whole repair. I repaired the suspension issue by replacing the 4 rods. The very last rod that I replaced was indeed bent. I closed the top and ran one load and then the lid lock issues... Read more

Ordered the springs and shocks. Noticed that the washer had placement for 4 springs, but the factory only installs 2 (or they forgot to install the other two on my machine). If you replace the springs, be sure to check for the spring bracket mount. You will also need those. The washer is running fine. Next I'll work on the dryer. Read more