Lid Lock Bezel Parts

• Will not drain
• Won't start
• Will not fill with water
• Lid or door will not open

My son was doing his laundry, only to announce that the washer wouldn't rinse, spin or drain. I looked on line at new washers and was staggered to see how much they cost, our Whirlpool is 20 years old! Then I looked on Craig's list to see about getting a used washer, but when I found something that looked good, and looked up how it performed, most of them had terrible reviews. So, I looked at a video that told about the 5 most common things to go wrong and figured out it was a broken lid... Read more

Replaced the door latch/lock assembly. Read more

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

• Door won't close

There is a video on youtube that talks about how to disassemble the electronic component out of the control board so I really won't go into that part of it. This disassembly of the control board will need to take place before you can even get started taking the gray piece out of the console to replace it. Be careful not break off the little tips behind the control knob, don't force it, it does come apart easily and there is an easy way to do it, that is also on youtube. This is where the... Read more

We had originally just replaced the door lock and it blew again. Started looking into it and found a thread saying the control board also needs to be replaced. Ordered both from here and now it’s working perfectly!! Don’t forget to put the pressure hose back on when reassembling the control board like I did!! Read more

I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely... Read more

Ordered a new timer and knob. The husband was able to fix in about 20 minutes and now works like new. Read more

• Door won't close
• Door stuck closed

This was much easier than expected. I called Appliance Parts Pros with my model # and you told me what part I needed. It was shipped the same day and arrived the next day. I removed the inner door trim with a table knife ( don't rush this or you might crack the trim ). I then unhooked the old door latch disconnected the spring from the door hooked on the spring from the new latch and clipped in the latch to the door. Final step was to reattach the door trim. It was very easy and all I used... Read more

• Doesn't shut off
• Won't start

Found the part through appliancepartspros.com The part was the cheapest of several web sites. although shipping for such a small part was steep ($7.95 If I was purchasing bigger parts or heavier parts..the flat rate cost would be a bargain. The part arrived the next day and fit perfectly. In additon; obviously the original manufactured part was not holding up well as the new part had a metal reinforcement band that will prevent the cracking in the future. Read more

The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more

I actually called a repair service in our area. The serviceman asked questions and detected that I didn't need a timer unit but thought it was just a knob that was required. He offered to come out but the expense would be considerable. I am SO relieved that it was indeed the knob, and the dryer was fixed. In this time in our lives, every penny counts. I must applaud the serviceman for his honesty and dedication to his trade. He directed me to this website, but also added if there were any... Read more

Conducted research on web, and via direct contact with AppliancePros where a diagnosis of replacing the water inlet valve and cleaning the sensor tube would "most probably" (80%) handle the issue. The remaining uncertainty would reside in the electronic board circuitry. The price of replacing the water inlet valve was half of a local repair call just to diagnose the issue so I decided to have faith in the odds presented to me. The part arrived on time, and using AppliancePros advice and... Read more

Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side. Read more

Replaced it. Read more

• Won't start
• Will not drain
• Will not fill with water

First, I ordered the wrong part (not paying attention to the model number on my machine...) I installed the part, following the very excellent video instructions from the website. I got the machine all put back together, but the electrical connection did not match! So, just a few days from leaving on vacation, I chatted online with the representative, Robyn C., from AppliancePartsPros.com. She was so helpful, double checking that the model number of my machine matched the new part, and... Read more