Power Strike Small Engine Regular Starter Parts

• No heat or not enough heat
• Too hot

Since the dryer was 24 years old I opted to replace all the possible problem components, instead of just the bad one. The parts aren't that expensive and do to their age I figured it was worth it to avoid having to go back into the dryer in a few months. The repair was surprisingly easy and went pretty much as the video instruction AppliancePartPros provided with one exception. Because, my model was much older than that used in the video, I had a more difficult time replacing the Heating... Read more

• Takes too long to dry

After I cleaned out the typical 1.5 pounds of lint from the vent, ( I do it every 2 months), I went searching for a solution. I found 6 possible causes on this site and purchased everything except a new burner; I wasn't going to go that far. Let the fun begin. Since my vacuum was still nearby, I thought I was ready for anything. Wrong. After I watched all the videos again for reassurance, I went in with screwdriver in hand and laptop nearby. I removed the top and looked inside. Don't be fooled,... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

I watched your video and had it fixed in less than 1 minute! Read more

Unscrewed door latch and replaced it with the new door latch (1-2 min). Unscrewed outer plate from door lock assembly. Removed door lock assembly from its outer plate and unplugged wiring. Replaced with new door lock assembly, plugged back in, tightened some screws, double-checked alignment between latch & lock assembly was good and the project was done. Incredibly easy and saved about $150 not having a repair tech come out to fix it. Read more

• Doesn't shut off
• Won't start

I watch the video on YouTube. And it went step by step on how to take it off and on Read more

Ordered parts from Appliance Parts Pros and replaced them.Works like new Read more

• Won't start
• Lid or door won't close
• Door latch failure
• Will not agitate

Superfast parts delivery. Got packages by the second day. Videos were extremely helpful and well done; we couldn't have done without them although we came across slight differences in our machine and found workarounds. Our machine did not drain the water so I drained the water manually via drain tube at bottom of the machine and checked the filter for blockage. All clear so I read articles on the internet and watched videos and took a chance on replacing the drain pump and circulating motor... Read more

• Won't start

Noticed Rolls on the top shelf no longer frozen, though the meat around it still was. Note: This is a good test, keep something that thaws quickly and is not expensive on top shelf, to act as a barometer for your freezer health! I first found a trip online to advance the defrost timer, as a failed timer is a common issue. I advanced the timer, but nothing happened. I emptied the freezer, then removed the thermostat and tested it. No continuity! With the Freezer continuing to thaw, I... Read more

• No heat or not enough heat

I replaced the "heating element" which was bad.........as well as the "Thermst-fix" and "Thermal Cutoff" which are located on the side of the element mounting location while I had the dyer all opened up and the element mounting tube removed.......I also replaced the Dryer Thermister which is located on the top of the blower fan.....To get to these parts, you must open the top of the dryer which has spring latches on both sides of the front corners... they need to be pressed in (use a putty... Read more

• Lid or door won't close

This was a super-easy repair. You have to line up the spring so that it sits on the bumps inside the magnet holder and the door, then you have to line up the tabs on the magnet holder so they will slide into the slots on the door. Then you just push it in. Repair took less than a minute. Read more

• Will not drain
• Won't start
• Will not fill with water
• Lid or door will not open

My son was doing his laundry, only to announce that the washer wouldn't rinse, spin or drain. I looked on line at new washers and was staggered to see how much they cost, our Whirlpool is 20 years old! Then I looked on Craig's list to see about getting a used washer, but when I found something that looked good, and looked up how it performed, most of them had terrible reviews. So, I looked at a video that told about the 5 most common things to go wrong and figured out it was a broken lid... Read more

• Shuts off too soon
• Too hot
• Takes too long to dry
• No heat or not enough heat

My appliance repair guy checked out the problem, but the stack washer dryer required the contractor to dismantle the cabinet to allow the repair to occur. So i wanted the parts available for the repair, so we would not have to have the dryer pulled apart in a small space for an extended time i ordered the parts on Friday afternoon and they arrived at my home before noon on Saturday! The contractor and the repairman were able to coordinate the repair on Tuesday morning, and though the... Read more

• Clicking sound
• Won't start
• Freezer section too warm
• Fridge too warm

Removed back cover and installed new start device. Plugged in refridgerator and it runs like new. Read more

Removed Torx screws inside the dishwasher door, this causes the door panel to fall forward/down. Having a rug or something underneath to prevent scratches is useful. It's about 8 screws that need to come out, if I recall correctly they are all the ones with the torx head facing into the dishwasher when in the closed position. Then the panel comes off, exposing the bolts holding the handles, the cap comes off easily and replaces easily and reverse the process. Some of the screws are different... Read more

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more