Yard Machine Small Engine Spark Plug Parts

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

• Will not dispense detergent

1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve. Parts $220 for Dishwasher Estimated Labor $400.00 Labor $0.00 Parts $100.00 for Pullout Faucet Estimated Labor $175.00 Labor $0.00 Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

• Will not dispense detergent

I bought a replacement part and changed it out. Read more

Replaced sump because the seal is not sold separately. You will need a skinny clamp after cutting the original swaged clamp off. Also Had to replace the cover as its seal is not sold separately either. Used dish soap on seals during assembly. Read more

Although I ordered the latch, lever and a new cup and replace the original pieces the dispenser still did not close. On further inspection it turned out to be a small spring that had fallen out of place. Once the spring was reconnected the dispensing cover worked fine. I'm still happy that I replaced the entire assembly with new parts regardless. Discovering the loose spring took the most time. Read more

I ordered a new detergent dispenser and control assembly, watched a few videos on you tube and dived in. The repairs were pretty simple once I got started and while I was doing this I went the extra step and cleaned out the drain. I would suggest doing this annually. Pretty simple to do and only 5 screws to get to the drain and the grinder. I found plastic and several other things that would not allow the dishwasher to drain properly and probably part of the problem of dishes not getting... Read more

Took cover completely off and tried putting back, could not match up left screw with available screw hole. Tried many different configurations and sequences to make this happen. watched a video on changing the front panel, the door in it had four screws, mine 2, no help there. Searched on the hyperextending issue, found an article about dogs and kids [had both here] climbing on the door and to check the springs and linkages. Linkages intact both sides, R [opposite] side spring very stretched.... Read more

We ordered the dispenser cover kit. the problem was with the spring. followed your "how to" video and it was a quick and easy fix! Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

I did not see the old ones fall out, so I was not sure the exact product placement within the rail, which was frustrating, to say the least. For the next person's benefit....these slide into the MIDDLE of the rail that is attached to both sides of the dishwasher. Not the front, not the back, but the middle! Steps to fix: 1) Order 2 of these Roller Bearing Cage. 2) Order 4 of WD12X10304 (AP4484666) end caps!! Unless you have brand new ones already, you will need them for sure and they are... Read more

I watched the video on your site and it showed step by step how to replace the spring. Excellent shipping time. Good customer service on chat forum. Read more

This was a pretty easy fix. Removed the screws around the perimeter of the inside cover of the door and pressed the outer door cover upward to release it from slots retaining it. There are four wires to remove (2 for the detergent door release and 2 for the rinse agent release). Removed the 6 screws retaining the dispenser assembly and inserted the new one. Reassembly is simply in reverse order. Problem solved for less than the cost of a service technician's call! Read more

Replaced dispenser Read more

Looked for the parts at this site and ordered those need plus spares Read more