Long Lite Small Engine Start Switch Parts

This replacement switch restores reliable on/off control for the specific function it serves in your appliance. A failing switch can cause that feature to stop responding or behave intermittently; replacing it brings normal operation back.

• Opens and closes the electrical circuit to the associated component when actuated
• Provides consistent, safe control of the feature it operates
• Typical failure symptoms: function won't turn on, won't turn off, or works only intermittently
• Physical clues can include a loose or sticky actuator, heat discoloration, or visible arcing damage

• Disconnect power at the breaker before servicing; allow hot surfaces to cool
• Access the switch per your model's service/parts diagram and note wire positions
• Transfer wires one at a time to the new switch; secure any mounting hardware
• Verify continuity and test operation before reassembly; replace any damaged connectors

If your gas burner won't light or clicks continuously, this igniter switch mounts on the valve stem to restore reliable ignition. Takes 5 minutes to replace.

Fix intermittent burner failures or electrical issues with this range wiring harness. Restores power flow when connections are loose, burnt, or broken.

The Switch is an OEM replacement part for Whirlpool refrigerators. It is designed to control the water dispensing function of your refrigerator, providing a convenient and easy way to access filtered water. It is responsible for activating the water flow when pressed, allowing you to dispense water into your glass or container.

A bad refrigerator water dispenser switch can occur due to wear and tear, physical damage, or electrical malfunction. If you notice symptoms such as the switch not responding when pressed, inconsistent water flow, or a complete lack of water dispensing, it may be time to replace the switch.

Symptoms of a bad refrigerator water dispenser switch include:

• Switch not responding when pressed
• Inconsistent water flow
• Lack of water dispensing

Restore your refrigerator's water dispenser by replacing the faulty or damaged water dispenser switch with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This is a factory switch used in the appliance's control/safety circuit. Replacing a worn or failed switch restores reliable signaling so the selected function engages properly and the unit responds consistently to user inputs and status conditions.

• Provides an electrical on/off signal to the control or safety circuit
• If faulty, selected functions may not activate or may be intermittent
• Can trigger error codes related to a switch input, depending on model

• Disconnect power before servicing; turn off gas/water if applicable
• Note/photograph wire locations and transfer connectors one at a time
• Verify actuator alignment and secure mounting before reassembly
• After installation, run a test cycle to confirm proper operation

Refrigerator not cooling or compressor running hot? This start device kit includes relay and overload to restore proper compressor function. DIY install.

The fan control switch is the panel-mounted switch that sends power to the appliance's fan motor. Replacing a worn switch restores reliable on/off control and proper airflow so the fan starts and stops when it should.

• Provides user-operated on/off power to the fan/blower motor
• Helps regulate airflow for cooling, venting, or convection depending on model
• Typical symptoms: fan won't run, runs continuously, intermittent operation, or a loose/broken switch shaft
• Mounts behind the control panel and is actuated by the exterior knob/lever

• Disconnect power at the breaker before servicing
• Remove the control knob/actuator and panel trim to access the switch
• Note wire positions or take a photo; transfer wires one at a time to the new switch
• Secure with the original hardware, restore power, and test operation

Burner won't spark or ignite? This surface burner ignition switch triggers the spark module when you turn the knob. 45-minute DIY repair for ranges.

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

This is a small electrical switch mounted near the dryer door opening that detects whether the door is open or closed. It completes the circuit that allows the dryer to run when the door is shut. Replace this switch if your dryer won't start, stops mid-cycle, or runs with the door open.

Washer won't respond to cycle selections? This selector switch mounts behind the control knob to restore reliable setting changes. Easy DIY fix.

Fridge not cooling but lights work? This compressor overload stops overheating and prevents startup damage. DIY-friendly repair in about 1 hour.

If your hood won't turn on or respond to controls, this switch may have failed. Requires removing the grease filter and lower pan to access and replace.

Interior light stays on or won't turn on? This upright freezer door switch controls lighting when the door opens and closes. Simple fix for most DIYers.

Fan or light not responding? Intermittent operation or loose controls? This range hood switch restores reliable on/off control. Simple DIY fix.

If your electric range burner won't heat properly or won't turn off, this infinite switch controls power to the surface element. Moderate DIY repair.