Power Small Engine On-Off Switch Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3405281
Dryer won't stay running after releasing start button? A faulty power relay is often the cause. This relay keeps the motor spinning consistently.
Do-It-Yourself Stories from Customers like You
Dryer motor would not stay in operation after releasing start button Gary P. • Wilton , NY • October 13, 2014
Googled the issue and was told to replace the motor relay. I ordered new relay form App. Parts Pros and it arrived in less than 2 days. After some relatively simple dis assembly of the dryer I replaced the relay. Dryer works fine now.
Read more
More
$34.75
- Compare At:
-
$41.35
- You Save:
-
$6.60
Genuine Whirlpool part
By: Whirlpool
Part Number: WP74003122
Fix a burner stuck on high or won't adjust temperature with this infinite switch. Controls cooktop burner heat levels. DIY repair in under 30 minutes.
Do-It-Yourself Stories from Customers like You
Element would stay on high even at lower settings why it would fail in the "high" mode is not a good design David M. • Suffield , CT • February 04, 2015
Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element
Read more
More
$61.56
- Compare At:
-
$73.26
- You Save:
-
$11.70
Genuine Frigidaire part
By: Frigidaire
Part Number: 134711300
Fix dryer heating issues with this thermistor temperature sensor. Solves intermittent heat, cycle errors, and poor drying. Easy DIY repair.
Do-It-Yourself Stories from Customers like You
No heat burner running 30 seconds at a time then turning off John G. • Oxford , MI • September 02, 2019
Replaced all sensors, limiters, thermistors, thermostat. Works great now.
Read more
More
$56.95
- Compare At:
-
$67.20
- You Save:
-
$10.25
Genuine Frigidaire part
By: Frigidaire
Part Number: 5309918806
This door-activated light switch controls the interior lamp in your refrigerator. Replace a worn or sticking switch to restore dependable lighting and prevent the bulb from staying on and warming the compartment when the door is closed.
- Opens and closes the light circuit as the door is opened and closed
- Helps prevent the light from staying on with the door shut
- Common symptoms: interior light won't turn on, stays on with the door closed, or works intermittently
- Physical signs may include a stuck/broken plunger or damaged housing
What's included: One light switch Install notes:
- Disconnect power before servicing
- Gently pry the old switch from the liner/panel and release its locking tabs
- Transfer wires one at a time to the same terminals on the new switch
- Press the new switch fully into place; restore power, and test
Do-It-Yourself Stories from Customers like You
Light didnt turn on Robert R. • New Britain , CT • May 25, 2015
Well started with the bulb switch when that didn't work, i continue with the next switch which was the door switch, then it worked just make sure the light bulbs are good, because i went thru 4 bulbs
Read more
More
$37.53
- Compare At:
-
$44.29
- You Save:
-
$6.76
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4456905
Provides electrical connection and control for gas burner ignition on cooktop surfaces. Replace if burners won't light, produce weak sparks, or if you hear clicking without ignition.
Do-It-Yourself Stories from Customers like You
The front two electronic igniters on the stove top range stopped working Raymond L. • The Woodlands , TX • December 26, 2015
I called a rpair service. The men came to the house, torn apart the stove top and advised Replacement of the wire harness. The trip charge of $100 would be deducted from a repair bill of $350, thus they needed an additional $150 for parts and $100 for labor after paying the trip charge. I bought the harness for $60, and the star bits I needed for my drill for $10. My son and I installed the new harness in about 30 minutes, which included a thorough cleanup, saving us $180.
Read more
More
$116.50
- Compare At:
-
$138.63
- You Save:
-
$22.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10249845
This water level pressure switch senses tub water level and signals the control to stop filling and advance the cycle. Replacing a failed switch restores proper fill shut-off and allows the washer to move to wash, drain, and spin.
- Detects water level via air pressure in the attached hose from the tub air dome
- Signals the timer/control to close inlet valves at the selected fill level
- Enables agitation and spin only when the level is appropriate or the tub is empty
- Typical symptoms of a failed switch include overfilling or underfilling, continuous filling, cycle not advancing, or no spin
What's included: 1 water level pressure switch Install notes:
- Disconnect power and turn off water supply before servicing
- Access the switch in the control console or top panel; note wire locations for reassembly
- Transfer the pressure hose and wire connectors to the new switch one at a time; ensure the hose is clear, not kinked or cracked, and fits snugly
- After installation, run a quick fill test to ensure proper shut-off and cycle progression
Do-It-Yourself Stories from Customers like You
F35 sud f21 Theodorus V. • Renton , WA • September 13, 2014
YouTube, water level sensor, cleaned drain basket
Read more
More
$161.76
- Compare At:
-
$192.49
- You Save:
-
$30.73
Genuine Ge part
By: Ge
Part Number: WE4X757
Dryer won't heat or overheats? A faulty safety thermostat fails to regulate temperature. Test for continuity with a multimeter; moderate DIY repair.
Do-It-Yourself Stories from Customers like You
Faulty thermal fuse Phillip D. • Hagerstown , MD • August 23, 2015
Removed lid. Removed switch panel. Suspected open circuit in thermal fuse. Tested it with a multimeter first to confirm it had an open circuit. This part is obsolete. Contacted manufacturer and found part supercedes to a different part number Ordered part. (This website is very efficient. The part arrived with the 1.7 day promise time.) new fuse bracket is slightly larger due to supercession. Marked bolt hole locations and drilled new. Installed fuse. Re-assembled dryer in reverse order....
Read more
More
$67.60
- Compare At:
-
$81.12
- You Save:
-
$13.52
Genuine Whirlpool part
By: Whirlpool
Part Number: W11050715
This replacement switch restores reliable on/off signaling to the circuit it controls, helping your appliance start, stop, and respond correctly. A worn switch can cause intermittent operation, no response, or lights and functions that don't activate. What it does:
- Provides an electrical open/closed signal to enable functions like starting a cycle, powering a motor or light, or shutting a feature off
- Acts as a safety/position interlock (such as door, lid, float, or hood) depending on the model
- Typical symptoms include won't start, won't stop, light won't turn on/off, or intermittent operation
- Can be checked with a multimeter for continuity when actuated
What's included:
Install notes:
- Disconnect power before servicing; turn off gas or water supply if applicable
- Access the switch, note wire locations, and transfer leads one at a time to the new switch
- Mount securely, ensure the actuator aligns and wires aren't pinched
- Reassemble and test operation before finalizing
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Speed Queen part
By: Speed Queen
Part Number: 202937
If your washer overfills, underfills, or won't advance cycles, the water level pressure switch may have failed. Takes about 10-15 minutes to replace.
Do-It-Yourself Stories from Customers like You
Broken pressure switch Carole Y. • Yakima , WA • November 06, 2019
Bought part from you and got a repairman to put it in. Darlene of your staff found part I needed. Nice lady! Repairman charged $82 to do a 10 minute job. Not your fault!
Read more
More
$123.78
- Compare At:
-
$146.06
- You Save:
-
$22.28
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304493153
The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.
Symptoms of a bad door switch can include:
- Oven failing to automatically go into bake or warm modes after door closure
- Interior lights not turning on when the door is opened
- Control buttons/display remaining constantly lit instead of dimming
- Oven not heating or functioning properly in different modes
Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.
This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.
Do-It-Yourself Stories from Customers like You
Frigidaire microwave oven lights and timer work but oven doesn't heat Reese F. • Essex Junction , VT • August 16, 2015
I diagnosed this problem via the web and the advice was spot on. The problem was a failure of the bottom door switch. I used a multimeter to verify that the switched never closed properly. It took me a minute to figure out how to remove the old switch (press a release tab under the switch while simultaneously rotating counter-clockwise). That was about the most difficult part of the repair.
Read more
More
$64.39
- Compare At:
-
$75.98
- You Save:
-
$11.59
Genuine Ge part
By: Ge
Part Number: WE1M1002
This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.
- Provides overcurrent protection for the circuit specified by the manufacturer
- If the fuse is open, the appliance may be dead, won't start, or certain functions won't operate
- Helps prevent wiring and component damage from shorts or overloads
- Repeated fuse failures indicate an underlying electrical issue requiring diagnosis
What's included: 1 CCMR fuse (30A, 120V) Install notes:
- Disconnect power to the appliance before servicing
- Locate the fuse in its holder/block and inspect associated wiring for heat or damage
- Test the old fuse for continuity; replace only with the identical rating specified
- Never bypass or upsize a fuse; correct the root cause of the failure before returning to service
Do-It-Yourself Stories from Customers like You
The dryer would not turn on Roland S. • Richmond , CA • August 02, 2014
First I check the breaker for the dryer then I check the power cord and the ohms to the power cord when all this things were in working order I then check the ohms to the fuse to the control panel.
The fuse had no ohms so I got a pair on needle nose pliers pulled out the fuse and replace it worked just find after that
Read more
More
$53.69
- Compare At:
-
$63.35
- You Save:
-
$9.66
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10131836
Fix dryer underheating or overheating issues with this 140°F fixed thermostat. Restores accurate temperature control and stops erratic cycling. Easy repair.
More
$69.95
- Compare At:
-
$82.54
- You Save:
-
$12.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10411937
Dryer won't start or run? A faulty belt switch often causes this when the belt snaps or slips. This switch monitors belt tension and is a fairly easy fix.
Do-It-Yourself Stories from Customers like You
Drum wouldnt turn power to control panel but wouldnt start Andy S. • Arlington , VA • November 03, 2016
Replaced motor "triple switch" Part Number: AP6021090 and the thermal fuse
Read more
More
$28.43
- Compare At:
-
$33.83
- You Save:
-
$5.40
Genuine Ge part
By: Ge
Part Number: WB24T10147
This is a high-amp SPDT (single pole, double throw) switch used in the oven door mechanism. It detects whether the oven door is open or closed and signals the control to enable or disable certain functions such as the oven light or broil element. Replace this switch if the oven light does not turn on or off when the door is opened or closed, or if the oven does not operate correctly in relation to door position.
Do-It-Yourself Stories from Customers like You
Faulty self cleaning latch Gregory K. • Bel Air , MD • December 28, 2016
Replaced faulty latch with new latch. New latch was different configuration, but the fit was okay. The only issue was that the wires to the electric motor were just barely long enough.
Overall easy repair if you have a T15 Torx bit, phillips screwdriver, and 1/4" nut driver. Hardest part is removing the gas cooktop to gain access to the cleaning latch. 0. Turn off electric to stove; remove the cast iron grates, center caps/orifices, and catch pans from the stovetop. 1. Disconnect the...
Read more
More
$23.34
- Compare At:
-
$27.77
- You Save:
-
$4.43
Genuine Whirlpool part
By: Whirlpool
Part Number: WP31001192
If your dryer is overheating, running too hot, or taking extended times to dry clothes, a faulty cycling thermostat is often the cause. Easy DIY fix.
Do-It-Yourself Stories from Customers like You
No heat on dryer low setting insufficient drying even on high extended times to dry Thomas M. • Galax , VA • June 12, 2016
Ended up replacing the cycling thermostat which corrected the problem. Andrew C. was very helpful with considerations and return of unneeded parts as well as very informative technical assistance. Could not have been treated better.
Read more
More
$79.24
- Compare At:
-
$95.09
- You Save:
-
$15.85
Genuine Whirlpool part
By: Whirlpool
Part Number: WP31001590
Fix a dryer that won't heat or overheats with a new thermistor. This temperature sensor ensures accurate heating cycles. DIY repair in 30 minutes.
Do-It-Yourself Stories from Customers like You
Dryer ran but wouldn't heat the only thing i could find was the thremistor only real at 8 ohms instead of a little over 10 Ross M. • Ohiopyle , PA • October 24, 2016
Installed a new thermistor tempiture control and it heats up as it should.
Tools used was a ohlm meter, 1" stiff puty knife, #2 Philips screw driver, neadle nose pliers,1/4 & 5/16 nut drivers.
Read more
More
$59.48
- Compare At:
-
$71.38
- You Save:
-
$11.90