Lid Lock Bezel Parts

Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side. Read more

Watched a You Tube video on how to remove the bad lid lock, ordered a new part and installed. Read more

Replaced door lock switch. Read more

• Won't start
• Will not drain
• Will not fill with water

First, I ordered the wrong part (not paying attention to the model number on my machine...) I installed the part, following the very excellent video instructions from the website. I got the machine all put back together, but the electrical connection did not match! So, just a few days from leaving on vacation, I chatted online with the representative, Robyn C., from AppliancePartsPros.com. She was so helpful, double checking that the model number of my machine matched the new part, and... Read more

I first received the quality parts in less than 2 days. It took me 5 minutes to change out the timer and 2 of the minutes were finding where my fiancée put the Phillips head screwdriver. Unplug dryer first, remove top three screws from back panel. Pull old timer up and out, have new timer in hand and transfer one wire at a time. Once all wires are transferred, snap the new timer in its place. Replace your three screws, put knob on timer. Plug in dryer and test. Once completed, cleanup your... Read more

Ordered a new seal, and replaced it with a new one freezer works great now. Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

Replaced the lock lid mechanism. Read more

Ordered a new filter and filter holder Read more

Removed the old latch and put the new one on. Read more

Our Kenmore (Whirlpool) refrigerator's ice maker had stopped making ice. I searched YouTube and found a repair videos for this exact problem, finding one with a similar refrigerator and the identical ice maker. I learned that the Water Inlet Valve had likely gone bad and would need to be replaced. In the video the tech pointed out the small rubber tube inside the freezer that comes down from the ceiling of the refrigerator into the ice maker. This tube feeds it the water to make ice with and... Read more

Ordered new knob and replaced it, easy fix. I felt the part was a little pricey. Read more

I first did quite a bit of interaction with the AI chat and doing Google searches, as well as entering the diagnostic mode for the dishwasher. (NOTE: Retrieve the technical sheet stored underneath your dishwasher behind the front toe kick panel to learn all about diagnostics!) From this research, I determined three possible issues: (1) the door latch assembly might be malfunctioning, (2) the soap dish actuator might be malfunctioning, and/or (3) the main control board was faulty. The door... Read more

• Will not dispense detergent

Process was a bit more complicated than the videos I had watched online. Had to remove both front panel and control panel to get to soap dispenser. Removed wires to soap dispenser and rinse aide dispenser. Removed wire "harness" around the top and right side of dispenser. Pried back the clips to allow dispenser to be pushed out. It was helpful to have another person to hold the door open at this point. Bent clips back and reinstalled everything. New part works great. Read more

• Won't start
• Lid or door will not open
• Lid or door won't close
• Will not agitate

The washing machine would allow you to program it, and all the lights on the control panel would light up, but pressing start did nothing. I tried putting the washer in diagnostic mode, but was unable to do so. The machine was not showing any fault code. I originally thought it was a problem with the 'Start' button and I thought that I'd buy a replacement part from the original seller of the washer. I was told by the 'live help chat person' that the problem was likely in the washer user... Read more

Replaced dispenser Read more