Bottle Support Collar Parts

I replaced all 4 suspension rods and springs and now it spins very smooth. They weren't broken, just badly worn. It gave new life to my 15 year old GE Profile washer. They are basically springs, so they wear after a while. It was well worth the hour I spent fixing it. You need a good long reach to get to the back 2 and you have to take off the dampening straps and the control panel so you can gain access. All in all, I'm happy with the repair, although I though that these parts are bit... Read more

• Shakes and moves

After watching the video carefully and taking notes for step-by-step dismantling of the LG washer, I took it apart methodically placing each item on a table in the order removed. I was able to remove and replace the bearings with no problems following the tips and tricks. The spider did not seem to be in bad shape but since I had a new one, it seemed reasonable to replace it as well, but it was difficult to extract the old one from the drum. The bolts are assembled with weld glue, so it is a... Read more

After taking off the top and front panels to access the drum, it was easy to see what the problem was. The front drum support was worn through and the 3 drum support glides were gone. The rear drum bearing was also completely worn out. And while I had the dryer apart I also replaced the idler pulley and drive belt. The only hard part was putting the drive belt back on the motor shaft and idler pulley. The dryer is back to drying clothes like a new machine. Read more

Chopper screen was completely blocked. Chopper blades separated from the shaft. Retainer ring came off of the shaft but was able to re install the chopper assembly. Worked fine after cleaning the screen and reassembly the lower spray arm. Lower spray arm hub tab broke when removing so purchased a new one with a new bearing. Appliance Part Pros video was excellent and very helpful. Read more

I ordered a tub suspendion Kit for it. Read more

Easy project. 6-year-old appliance. If one is failing replace all 4. The plastic race that holds the bearings becomes brittle and breaks dropping the bearings into the dishwasher tub. Total project time from assembling tools, protecting the hardwood floor, removal, and installation was less than 2 hours. 1) Turn off power to the appliance. 2) Remove 2 mounting Phillips screws holding dishwasher in the cabinet. 2) use a 1/4” nut driver to remove the 2 screws holding the bottom plate from... Read more

Replaced dishwasher spray arm, spray arm support plate, dishwasher drain trap filter assembly. Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

I did not see the old ones fall out, so I was not sure the exact product placement within the rail, which was frustrating, to say the least. For the next person's benefit....these slide into the MIDDLE of the rail that is attached to both sides of the dishwasher. Not the front, not the back, but the middle! Steps to fix: 1) Order 2 of these Roller Bearing Cage. 2) Order 4 of WD12X10304 (AP4484666) end caps!! Unless you have brand new ones already, you will need them for sure and they are... Read more

The lower basket L& R track bearing brackets on my KitchenAid dishwasher (KDTE704DSSO) finally gave out (ball bearings everywhere) after (6) years of daily, family use. The service techs provided me with all the information I needed to successfully and quickly complete my project. My parts were mailed to me very quickly and my dishwasher was up and running in short order. The parts were clean and in perfect working condition. (After pulling your dishwasher out, there are two sets of screws on... Read more

I tore it apart using. YouTube videos to guide me and found the shocks were loose and floppy. I found the shocks in stock here and had them in my hand 2 days later for only $10 shipping! It runs great now! Read more

I contemplated replacing it but was able to find all the parts right here and fix it within an hour. Now it works great with no leaks. I have been using AppliancePartsPros.com to maintain all my appliances as it has saved me thousands of dollars over the years. Read more

I noticed my 5-year-old Samsung, front-loading washing machine started to sound like my kids were using it as a drum kit. I immediately checked it out and the stainless drum was wobbling so badly that I just took it for an unbalanced load of clothes. My gut was telling me that something was wrong because I had not remembered the machine being so loud before. I removed the clothes from the washer and I ran it empty to confirm my suspicions: the wobble was still there. I would say it had a 2"-3"... Read more

Removed the bottom rack from the dishwasher. Removed the 2 front plates at bottom of the dishwasher. Removed the two screws from the top of the dishwasher holding the dishwasher to the counter-top. Pulled the dishwasher out. Removed the 8 mm screws from the outside of the dishwasher-- 4 per side (Underneath the sound proofing). Pulled the old tracks and placed the new tracks into place and tightened the screws back up. Pushed the dishwasher back into place. Reinstalled the screws securing... Read more

I ordered the part and it was there in three days. I was so happy to get it and make the wife happy. Read more

Bought the drawer support, unscrewed the screw with a socket wrench, installed the new drawer support, wala! Took 1 minute. Moral to the story, don't overload that bottom drawer. Metal cookie sheets or the broiler pan is okay, but not big ceramic baking trays, they're too heavy for the nylon drawer supports. Read more