Power Strike Small Engine Start Switch Parts

Conducted research on web, and via direct contact with AppliancePros where a diagnosis of replacing the water inlet valve and cleaning the sensor tube would "most probably" (80%) handle the issue. The remaining uncertainty would reside in the electronic board circuitry. The price of replacing the water inlet valve was half of a local repair call just to diagnose the issue so I decided to have faith in the odds presented to me. The part arrived on time, and using AppliancePros advice and... Read more

I contacted AppliancePartsPros and gave them my symptoms and failure codes and they were able to diagnose the problem and send the correct parts to resolve the issue. This is the 3rd or 4th time I've used their service since 2012 and they have been correct on each and every repair issue I've had. Many thanks for the professional advice and help! Read more

• Too hot
• No heat or not enough heat
• Takes too long to dry

Replaced the thermostat and fuse it could have been either of them that was causing the issue - and now it works like a charm. Read more

After my layman's diagnosis (hope) of a bad micro switch to the ice dispenser (would not activate and dispense ice through the chute) I purchased the both the ice and water dispenser micro switches (kill two birds with one stone). Albeit the video attached to these parts may be helpful to some it was not applicable to my refrigerator, as you could not access it from the front by removing the exterior dispenser plate. Don't try this on the LG, LFX25991ST series, refrigerator or you may break it... Read more

• Shuts off too soon
• Too hot
• Takes too long to dry
• Won't start

Recommendations have fun and a bucket to prevent losing parts. First watch the videos, practice disassemble and reassemble the dryer drum. Make certain you have a good screw driver and spatula from kitchen (could not find my putty knife). Secondly, clean and inspect everything, make sure the motor bearing and belt pulleys are in good condition with little or no play. Third after you have confidently disassembled, vacuum cleaned, inspected all the worn parts, grease the motor and pulley,... Read more

• Won't start
• Will not drain
• Will not fill with water

First, I ordered the wrong part (not paying attention to the model number on my machine...) I installed the part, following the very excellent video instructions from the website. I got the machine all put back together, but the electrical connection did not match! So, just a few days from leaving on vacation, I chatted online with the representative, Robyn C., from AppliancePartsPros.com. She was so helpful, double checking that the model number of my machine matched the new part, and... Read more

Replaced door switch - it took less than 5 minutes - works perfectly Read more

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

Replaced door lock switch. Read more

In order to replace this, you must remove the "outer door". This service manual is a pretty good reference (page 37): http://members.msaworld.com/wp-content/uploads/sites/3/2017/02/2013-DW-Service-Manual.pdf Note that this specific dishwasher has 12 screws that need to be removed before the outer door can be separated. Once separated, don't even bother trying to push the broken handle out of the front as suggested. You will probably end up damaging the outer door. Instead, take some... Read more

Replaced the lid lock switch Read more

The help tech helped me troubleshoot what the problem might be, and we narrowed it down to a faulty switch. He helped us pick the right part, and the video was helpful - it gave me the confidence that I could fix it myself. The part came, and it only took me 5 minutes to change out the switch. Now my dryer works great! I saved my wife $500 for a new dryer! :) Read more

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

Replaced the lock lid mechanism. Read more

I think I have a lemon of a dryer. I keep having to pay someone to replace my heating element about every year. So I already had the heating element, but I thought I would replace the thermostat and the limiter also. Yes, I am a 46 year old mom, and I replaced all three items. Thank goodness to youtube! Ha! I have ordered from you before and you always send promptly. Thanks! Read more