Run Vent Thermal Fuse Parts

Replaced Thermal Cutoff sensor. Read more

• Will not stop filling with water

I replaced the water level switch and hose. After removing the hose, I found that it was clogged, and did not allow the water level to be sensed by the switch. A test after the replacement of the parts was successful. While filling the tub, the water shut off at the small, medium, and large levels as indicated by the switch. Read more

For several months we could smell a slight odor of propane in the laundry room and wondered why, just didn't seem like it was enough to be overly concerned, but thought something must be wrong with the dryer, but it was still working. We just didn't know how inefficiently. Then the extra time it took to dry a load of clothes progressively seemed to get longer, but things still seemed to work fine and the clothes got dried, given enough time. Then approximately 3 weeks ago we noticed the dryer... Read more

I had an appliance repair guy come and he told me it was possibly the vent assembly but if changing it didn't fix the problem it would be the control board next. He felt it was not worth the money to repair because he would have to disconnect everything just to get to the vent on the right rear top of the dishwasher. When i took the DW out thinking i had to buy a new one i saw this part was stuck open and covered in limescale deposits and grime.I ordered the part from appliance pros and payed... Read more

Needed installation parts. I ordered the parts from the company I purchased the appliances from. A week went by and no parts, called, emailed and called again to find out when the parts would arrive to be able to Re-schedule the installation. After the run around, I found AppliancePartsPros website and placed my order with them. I received the parts I needed within the time they promised. I was able to schedule my installation to enjoy my new appliance. It's been almost 4 weeks and still no... Read more

• Fridge too warm

The defrost heater element looked good and had continuity. The defrost thermostats checked good, so that just left the Defrost Module as the likely suspect. I installed a new defrost control module and thermostats. The thermostats were inexpensive and the old ones could have been intermittent, The only "tricky" part was finding out how to get to the back screw that holds the main control panel. Discovered that the return air duct surrounding the control panel needed to come off. It helps... Read more

Replaced defrost sensor in freezer compartment, if you are handy this is a do it yourself job. The cover in the freezer section just pops out not tools needed. You will need a few small zip ties and some cutters to remove the old zip ties. Take a picture were the old sensor was before removing and reinstall in the same place. I used a meter to check continuity of the defrost element and found the element to be ok. I was quoted $85 to have someone come to the house just to check the unit and... Read more

Replaced sump, wash pump, drain pump, diverter motor, and thermostat. Read more

Needed installation parts. I ordered the parts from the company I purchased the appliances from. A week went by and no parts, called, emailed and called again to find out when the parts would arrive to be able to Re-schedule the installation. After the run around, I found AppliancePartsPros website and placed my order with them. I received the parts I needed within the time they promised. I was able to schedule my installation to enjoy my new appliance. It's been almost 4 weeks and still no... Read more

Replaced thermistor Read more

• Fridge too warm
• Fridge runs too long
• Freezer not defrosting
• Freezer section too warm

My GSS20IETD BB side-by-side refrigerator had been having the ice form into a single mass over a period of a week after cleaning it out. It actually kept breaking my ice maker auger and pushing the slide-in tray or shelf over the ice maker up breaking it also. Frost would form all over food after about a couple of weeks. The ice auger motor would freeze up and stop turning. The coils did not have frost on them when I was able to view them. I replaced the thermistors in the freezer, defrost the... Read more

I had to remove the dishwasher about 6 inches then remove the door springs and remove the door. Next was to open the cover to reach the circuit board and remove it. The new board was put in and attached the plug. and put the door back together and reinstall the door and springs. Turned the power to check that the lights came on. After confirming I again had power, I turned the breaker off and reinstalled the dishwasher in the cabinet and restored power. Lastly I ran the machine to ensure that... Read more

I had previously replaced the transmission in my two year old Whirlpool Cabrio washing machine. Overall it was in good shape but gets heavy use. That repair was approximately $200 and worked for several months. Recently it began leaking. At first I thought it was the tub-to-shaft seal. I replaced this part but it was still leaking. It turns out it was the simplest of things... The drain hose was not connected very well! I replaced the drain hose ($11 part) and while I was at it I... Read more

The F9 error code is supposed to indicate that the door lock mechanism has failed. My oven would give the F9 code and turn off during normal baking at 400 F after about 30-40 minutes. It turns out that GE must have programmed the error codes incorrectly in my model, because the real problem was that my control board cooling fan was no longer functional, and one of the two thermal switches was shutting off the unit when the control board area got too hot. AppliancePartsPros.com is one of the... Read more

My first attempt was to replace the main board and then the thermistor, should have done this the other way around, turned out it was the thermistor, a pretty cheap part, dryer works great now. Repair requires removing the drum but overall not too difficult or time consuming. Read more

I replaced the hose between the tub and the pump. The clamp screws were quite rusted but I used a socket wrench on them since they have hex heads in addition to the screwdriver slot. If I had tried to use a screwdriver, I think it would have been difficult. I did not reuse the original clamps but replaced them with hardware store hose clamps. Read more