205Idn2ww Parts

• Will not agitate
• Spins slowly

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

• Pumps but will not spin
• Will not agitate
• Burning smell
• Touchpad does not respond

My whirlpool washer was no longer spinning, so my first stop was YouTube where I found the video from AppliancePartsPros showing how to replace the motor coupling. In addition to the replacement guide, Matt also shows you how to diagnose the problem by looking for rubber shavings under the washer. Seeing the rubber shavings under the washer, combined with the fact that the washer still drained meant that the motor was still working, so something else in the drive train was bad. I took the... Read more

• Spins slowly
• Pumps but will not spin
• Burning smell

A couple of years ago, I had an issue with my Whirlpool washer which is every bit of 18 years old. I checked the internet for what might be wrong and stumbled across some how to videos on how to fix it. So, the other day, when my washer quit spinning the first thing I did is go to the internet again to see if I would be able to fix again. Thank you, Appliance Part pro.com, for your very helpful website with the very informative video's on how to replace parts! After I watched a... Read more

• Leaks water
• Leaking
• Will not drain
• Fills and drains at the same time

After noticing a leak from the washer I got on YouTube and determined the likely cause was a bad drain pump. The repair looked easy enough, so I ordered a replacement part. Well.......the removal wasn't quite as easy as they showed on the video I watched. Supposed to slip right off after removing the retaining clips. Upon additional video reviews I saw that an old washer could have significant rust on the shaft onto which the pump is installed. And boy, did I have rust on my machine. I yanked... Read more

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Won't start
• Timer will not advance
• Will not drain

First I checked the circuit breakers and power to the outlet, then next wanted to check the lid switch, but it wasn't where I had found it on older models. I could hear it clicking on and off as I raised and lowered the lid, but it wasn't visible. I drained the tub through a siphon hose to lighten the machine, so I could slide it away from the wall to better see. Couldn't see the switch anywhere and decided it must be hiding in the raised console, but was unsure of how to attack it without... Read more

When I removed the cabinet, all of the springs appeared in tact, I had already replaced the counter balance spring so I knew that was not the issue. None of the suspension springs or brackets were broken but they did look worn/rusty so I replaced all of the brackets (2 in front and 1 large in back), all of the suspension spring retainers, and all of the suspension springs and it fixed the issue! I plan to also replace the Self leveling leg spring which is an easy fix since it's on the back of... Read more

Thanks to the Appliance Pro video and next day delivery, the fix was easy. Removed the old seals by hand and placed the new seals around the door shelves and eased it into the grove in the door. Read more

Removed freezer door by removing 4 bolts holding slide tracks for freezer basket. Pulled out old gasket. Soaked new gasket in hot water to smooth out a crease that resulted from shipping. Installed new gasket, starting at corners. Used a blunt tool to push new gasket into slot at the corners. Set remaining gasket material with hands. Used putty knife to tuck edge of gasket under lip along door. Reinstalled door. Take care to line up door perpendicularly. There is some play when... Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

• Leaking

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

Looked up the parts and ordered new parts. This business was great. The order was here fast, and easy to track. Also loved they had the video attached to the part I ordered for easy change out. Would recommend them to anyone for repairing your appliances. They make this easy for finding the part and installing yourself. Read more

• Will not stop filling with water
• No hot or cold water
• Will not fill with water

Replacing the water inlet valve fixed the problem. For many months we noticed cold water was just dribbling into the washer during the rinse cycle, and "warm" washes were hot not warm. It seemed like the cold water wasn't able to enter the machine. Then one day the cycle just stopped when it reached "rinse" and wouldn't go any further. I first tried solving it by cleaning the filter where the cold water hose enters the machine at the back. It was coated in sediment (the water comes from a... Read more

• Shakes and moves
• Noisy
• Pumps but will not spin

Replaced washer drive block and Cam. I called around and finally settled on Appliance Parts Pros because they helped diagnose the problem, told me what parts to replace and had videos to show me how to do it. In completing the repair I had to remove quite a few pieces of hardware in order to get at the part I was to replace. The videos helped but there is a learning curve while you familiarize yourself with the parts and figure out how the remove them. Eventually I got to a large nut that,... Read more

First went through the troubleshooting guide on the website and read the various stories and watched the repair videos for replacing the springs and suspension pads. Then before ordering any parts disassembled the machine only to the point of removing the cabinet to see if there were any obvious issues. The springs appeared OK but I couldn't tell of they were fatigued or not and all were in place but the tub suspension pads were definitely worn out. I then put the machine back together and went... Read more

With the correct part, I was able to replace the broken assembly and attach the roller and put the crisper pan onto the assembly. Read more