Axxis Parts

The Door Seal is an OEM part for Bosch front load washers, designed to ensure a watertight seal between the door and the drum. This part prevents water from leaking out during the wash cycle, maintaining the efficiency and safety of your appliance. 

Over time, the constant exposure to water and detergent, along with the physical stress of laundry loads, can cause the door seal to degrade. 

Symptoms of a bad Door Seal include:

• Visible signs of wear, such as cracks, holes, or tears, which can lead to water leaks.
• Mold or mildew buildup, resulting from trapped moisture and detergent residue, which can cause unpleasant odors and potential health issues.
• The door struggling to close properly or water leakage during the wash cycle, indicating a seal that has lost its elasticity or is otherwise damaged.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Fastening Ring is an OEM part for Bosch front load washers. It secures the door boot seal to the front panel of the washer, ensuring a tight and leak-free connection. This ring is essential for maintaining the washer's seal during operation, preventing water from escaping the drum.

Causes of a bad fastening ring can include normal wear and tear, rust or corrosion, and damage from over-tightening or mishandling during maintenance.

Symptoms of a bad fastening ring include:

• Water leaking from the door area
• The door boot seal becoming loose or detached
• Visible damage or deformation of the ring

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This door seal holding spring is the wire clamp that secures the washer's door boot to the front opening, keeping the seal seated to help prevent leaks and maintain a proper fit.

• Holds the door seal/boot firmly around the front panel opening
• Helps maintain a watertight seal during wash and spin cycles
• Replaces a stretched, broken, or missing clamp/spring
• Common symptoms: boot won't stay seated, water leaking at the door opening, visible broken/missing spring

• Disconnect power and turn off the water supply before servicing
• Open the door and carefully remove the existing clamp from the gasket groove; avoid puncturing the boot
• Reseat the boot evenly, then stretch and position the new spring/clamp around the groove (spring typically at the bottom)
• Test for leaks after reassembly

The Carbon brush, drum motor is an OEM part for Bosch washing machines. These carbon brushes are responsible for transferring electrical current from the commutator on the motor to power the rotary movement inside the washing machine drum.  Two come per package.

Symptoms of a bad carbon brush, or drum motor can include:

• noisy or squealing sounds coming from the motor during the operation  
• the drum fails to spin or spin inconsistently
• the washer is unable to enter spin cycles
• slow or reduced agitation 

Causes of a bad part include normal wear and tear over extended use. As the brushes continuously contact the commutator, friction can cause them to wear down over time.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This Drain Pump is an OEM part for Bosch Washers. It facilitates water drainage from the washer during the cycle. Continuous use and debris accumulation can affect the pump's performance.

What Causes a Bad Drain Pump:
Debris, foreign objects, or wear from continuous use can lead to clogs or mechanical issues with the drain pump.

Symptoms of a Bad Drain Pump:

• Standing water in the washer drum after the cycle
• Slow or incomplete drainage
• Unusual noises during the drainage cycle

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This front door panel replaces the outer frame of the washer door, restoring appearance and proper alignment. It frames the window and interfaces with the handle/latch components so the door closes and latches as designed.

• Forms the exterior frame around the door glass and completes the door assembly
• Provides alignment for door components to help ensure smooth closing and latching
• Replaces cracked, broken, or discolored outer door trim/panel
• Can help resolve issues like loose-feeling doors or doors not aligning with the latch

• Disconnect power before servicing
• Open the door, support the assembly, and remove the perimeter screws securing the outer panel
• Transfer any components attached to the old panel, position the new panel, and tighten screws evenly
• Check door alignment and latch operation before returning the appliance to service

The Drum Drive Motor is an OEM part for Bosch washing machines. This motor powers the drive system that rotates the wash drum and tumbles clothes during cycles.

Causes can be normal wear and tear over time spent rotating heavy loads daily. Failure of motor windings from years of continuous use is also common.

Symptoms of a bad drum drive motor include:

• The wash drum failing to turn or tumble clothes
• Abnormally long cycle times
• Strange noises coming from the motor area
• The machine not advancing through cycles

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Restore smooth, secure door movement with this door hinge. It supports and guides the door through opening and closing, helping ensure proper alignment and consistent sealing so the appliance operates safely and efficiently.

• Supports the door's weight and pivots for smooth opening/closing
• Helps maintain correct door alignment and gasket contact
• Wear or damage can cause sagging, misalignment, noisy operation, or incomplete closing
• Replacing a worn hinge can improve door seal and overall performance

• Disconnect power and allow the appliance to cool before service
• Support the door during removal to prevent strain on the remaining hinge
• Transfer any original fasteners to the new hinge if re-used
• Check door alignment and operation before restoring power

The Drive Belt is an OEM part for Bosch washing machines. This belt connects the motor to the drum, enabling the drum to spin during the wash and spin cycles. This belt measures  49.4 inches and replaces a broken or damaged original belt. With 5 ribs and 4 grooves, the high-quality belt transfers drive power to rotate the drum.

Causes of a bad drive belt include normal wear and tear over time, overloading the washer, or a misalignment of the belt and pulleys. These issues can reduce the efficiency of the washing machine and cause it to malfunction.

Symptoms of a bad drive belt include:

• The drum not spinning or agitating
• Unusual noises during operation
• Burning smell from the washer
• Washer stopping mid-cycle

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This latch secures the appliance door closed and lets the control know when it's safe to run a cycle. Replacing a worn or damaged latch restores reliable door closure and consistent cycle starts.

• Engages the door strike to hold the door shut during operation
• May include an internal switch that signals door-closed status to the control
• Helps prevent cycle interruptions caused by a door-ajar condition
• Common symptoms: door won't latch, door pops open, cycle won't start, "door open" message or beeping

• Disconnect electrical power before servicing; shut off water supply if applicable
• Access and fasteners vary by model; latch mounts at the door/front panel area
• Transfer any mounting hardware and connectors from the original part one-for-one
• After installation, verify proper alignment with the door strike and that the unit recognizes "door closed"

This valve magnet is the solenoid actuator used to open and close a dishwasher water/control valve, restoring proper water flow for filling and cycle operation. It replaces a failed or weak magnet to help the valve respond correctly. What it does:

• Converts electrical signal into linear motion to operate the dishwasher valve
• Restores valve opening and closing when a worn or stuck magnet causes fill or circulation issues
• Commonly used when dishwasher won't fill, stops mid-cycle, or shows related valve/fill errors
• Works with the valve body; does not include seals or the full valve assembly

• Disconnect power and shut off the water supply before beginning service
• Replace with the matching OEM magnet and ensure proper seating on the valve body
• Keep terminals dry and secure electrical connections; inspect gaskets and valve body for damage

This is a valve magnet intended for use in washing machines. The valve magnet's purpose is to allow water to flow into the appliance during the different washing and rinsing cycles.Signs that indicate the valve magnet is malfunctioning or damaged include the washing machine shutting off before the cycle is over, water overfilling the machine, or water not shutting off at all. The replacement of the part is a simple process. Disconnect the appliance from its power source first. The water connections should also be shut off and removed from the washing machine. Wear gloves for safety. Ensure all connections are secure before reconnecting the device to the electrical outlet.This valve magnet is a genuine OEM replacement part. It is sourced from the manufacturer. The valve magnet is sold as an individual unit. The part is made of durable, high-quality materials. It can be installed in several models of washing machines. It is compatible with devices produced by Bosch, Thermador, and Gaggenau.

This replacement foot supports and levels your appliance so it sits steady and operates smoothly. Replace a worn or missing foot to restore proper height, reduce wobble, and help protect surrounding surfaces.

• Supports the base/frame to maintain proper height and alignment
• Provides leveling adjustment so the unit remains stable
• Helps reduce rocking, vibration, and rattling during operation
• Replace if the original foot is cracked, stripped, missing, or won't adjust

• Disconnect power; shut off water or gas supplies if applicable
• Carefully tilt or raise the unit to access the foot location
• Remove the damaged foot and install the new one per design
• Level the appliance front-to-back and side-to-side; verify stability before use

This door hinge bushing sits between the hinge and pivot point to reduce friction and wear. Replacing a worn bushing restores smooth, quiet door movement and helps keep the door properly aligned over time. What it does:

• Provides a smooth, low-friction pivot surface for the hinge
• Helps maintain door alignment and consistent opening/closing feel
• Reduces squeaks, grinding, or binding from the hinge area
• Replaces cracked, flattened, or missing bushing that can make the door feel loose or stiff

• 1 door hinge bushing

• Disconnect power to the appliance before servicing
• Support the door to relieve hinge tension; hinges may be spring-loaded—control door movement
• Access the hinge per your model's service information and note the bushing's orientation
• Install the new bushing, reassemble, and test door travel and latching

This drum bearing set replaces worn bearings that support the dryer drum and enable smooth, stable rotation, restoring quieter operation and reducing wobbling, grinding, or squealing caused by failed bearings. What it does:

• Supports and stabilizes the drum shaft to maintain smooth drum rotation.
• Replaces worn or noisy bearings that can cause loud squealing or grinding.
• Reduces drum wobble and vibration that can lead to rubbing or uneven wear.
• Helps restore proper drum alignment for smoother operation.

• Disconnect power (unplug the appliance or switch off the circuit) before starting any repair.
• Replacement typically requires drum access/removal and basic hand tools; inspect the appliance service manual or diagram for disassembly steps.
• Inspect the shaft, seals, and surrounding components for wear while the drum is removed and replace any damaged parts.

This water inlet hose gasket seals the connection between the supply hose and the appliance's inlet fitting. Replace a flattened or damaged washer to stop drips at the coupling and restore a reliable, watertight connection.

• Creates a watertight seal at the inlet hose-to-appliance connection
• Helps prevent drips, puddles, and water damage around the machine
• Replace if the old gasket is cracked, hardened, flattened, or missing
• Common symptoms: leaking at the hose coupling or needing to retighten the fitting to stop drips

• Disconnect power and turn off the water supply before servicing
• Place a towel to catch residual water, then detach the inlet hose from the appliance fitting
• Remove the old gasket from the hose coupling and seat the new gasket evenly
• Reattach and hand-tighten the coupling; open water supply and check for leaks—do not overtighten