Fan Cover Parts

• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

Much easier than expected, I was certain it had to be a water line but the solved everything Read more

Went on line to check troubleshooting sites, then went on UTube to watch a video on how to repair the appliance, then ordered the part from you, the used the video as a guide to replace the part. worst part was getting the clip off the fan blades and the putting it back on Read more

I replaced the warped cover guide and the lint filter. Now it works perfect! Sears was going to charge $100 just to diagnose the well known problem, not including parts and labor. It only requires 4 screws(i used the old ones). Easy fix. Read more

Shut off power in the panel box - easier than getting at the plug behind the unit. Had to take out the lower full-width drawer and the two crispers next. Removed two screws on the shelf above the wide drawer and removed the two shelf parts. Next was removing a screw from each wide drawer support. Then I pulled the support forward about an inch to disengage it from a post towards the back. There is a wiring connection in the right-hand support you will need to disconnect. Next, I removed a... Read more

In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more

The part went on easily. U Tube video answered any questions I had before installing. Read more

• Will not tumble
• Takes too long to dry
• Noisy

I FOUND the website on t internet, found my part ordered it and watched the how to video ,repaired the dryer myself. Awesome Website. Read more

I have order three parts, guide filter, cover guide, and sensor assembly. My previous cover guide was from two parts, when sensor assembly was one of them. New part ( guide cover ) was all in one piece so I just transfer old metal part of sensor to new cover guide and I don't need that sensor assembly anymore. I have ordered all three parts overnight by Fedex, ordered 15 min before 5pm, so next day it was here. Dryer is fixed, I'm happy. Read more

Top mounted freezer with bottom refrigerator. Kenmore Elite Shut off the power Remove all food stuff from freezer (placed in ice chest) then shelves. Removed the ice maker, (easy!) 3 screws and unplugged wires. 2 screws in the back panel. Pulled top forward - downward Unplugged wiring harness from back wall of freezer, removed ground wire from panel Pulled fan blade off. (Fan was attached to back wall, not removable back panel) Removed 2 screws to get to fan motor. 'Unsnapped ' motor... Read more

It was after 11:00 at night a few nights ago, I couldn't sleep listening to the whining of the fan in the freezer, it was running and making noise sounding like waaoooww, waaaoww. It also sounded like grumbling of a garbage disposal. The refrigerator fan motor was so noisy it was keeping me up all night going on and off running really loud and about to fail. So I was desperate, and called AppliancePartsPros when I couldn't get to sleep near midnight because the fan was so noisy and Bud in... Read more

I wanted to avoid pulling the drum. Luckily, my blower was easily accessed by pulling the front bottom panel. A couple of sheet metal screws were all I needed to remove the fan housing cover. I knew the fan was on reverse threads, i.e. righty-untighty. As it spins it tightens so no need for a retaining nut. I took off a screw holding on the exhaust tube and wiggled it out. I found the broken teeth inside. With the tube out of the way I was able to slide a crescent wrench in back and place... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

• Noisy
• Fridge too warm
• Freezer section too warm

I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks Read more

• Fridge too warm

Fan motor went bad. Fixed the fridge for less than it would have cost me just to have someone come out and look at it. Read more

• Fridge runs too long

First, cleaned all the dirt and lint from the condenser radiator, the fan motor is in a metal housing holding the fan motor in place. look carefully and there is a sheet metal screw at the bottom of the housing, 1/4 inch screw head sheet metal screw. I removed the screw and that released the housing from the base of frig. then very carefully , I turn the housing with the fan motor still in the housing a worked out of the frig base where it would be easier to replace the bad motor. the... Read more

• Doesn't shut off

I only needed the Bracket Assembly motor, not the DC Motor or Fan Assembly that I also ordered so I will be sending those back. The repair was extremely straightforward with a few bumps along the way. All told it took me about an hour. I started with shutting off the breaker for the refrigerator and putting all of the frozen food in coolers. Then I removed the drawers and the bracket for the drawer rails on the left side (as your facing the refrigerator). I then proceeded to gently pry off the... Read more