Gtwwn2800d1ww Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

Noticed that lid lock light was not on, googled problem, ordered parts, working on 3rd day. Read more

• Too warm
• Clicking sound
• Won't start
• Freezer section too warm

I have a Kitchen Aid side by side refrigerator/freezer which is 8 years old. One day it just stopped cooling. At first I was just going to junk it and purchase a new one. However, I took off the lower back cover and noticed the compressor was not running. I knew from experience that these compressors need a starter capacitor and relay and it is not uncommon for these parts to fail. I looked on the Internet for a video which showed how to remove the parts. I also found a video which showed how... Read more

I opened the cover panel of the control board. I visually checked for burns on the board and verified all connectors were firmly seated. I opened the bottom of the unit, and I saw the service manual in a zip-lock bag. From this manual, I verified that the drain pump resistance is good, the start capacitor is good, and the lid switch is good. I entered diagnostic service mode. Persistent alarms are 4 and 25.Error 4 means Reset Monitor, while Error 25 means Pressure Sensor Dropout. I... Read more

I found a YouTube video, order the parts about midnight Saturday and-they came in the mail before lunch on Tuesday. I laid the washer on the rear panel, removed both pulleys to clean them, installed the speed sensor. bolted the pulleys back in place, installed the new belt-making sure it was centered and everything moved freely, and attached the belt/pulleys cover. I set the washer back up, reattached the water lines, placed the drain tube, and plugged in back in. Works like new !!! 30 minutes... Read more

Replace belt. Read more

Replaced all 4 rod and spring assemblies. Read more

Replaced all 4 rod and spring assemblies. Read more

GE Washer m/n GTW460ASJ6WW would allow other fill levels, but when set to "super" it would never stop filling. Checked water inlet valve (by initiating a fill and unplugging the unit) to see if the inlet valve was sticking open, that was not the issue. Decided to replace the board even though it is a significant fraction of the cost of a new washer. Local appliance stores didn't have the board but APP did, and of course, they are open 24/7 while my local part stores have decided the weekend is... Read more

I put this repair off for a long time because I knew the machine would have to be completely torn down to fix it. The repair videos give you the impression that this condition is caused by a bad 'Tub Bearing' which takes a long time to replace but only costs about $15. Don't be lulled into thinking you can fix this for $15. The 'Tub Bearing' is really only a bushing. The one I removed from my washer looked fine but I replaced it anyways. The real problem here is GE's poor design which allows a... Read more

Replaced the belt. Read more

After researching the problem on this site, I realized that the most likely cause was a bad bearing contained in the shaft & tube assembly. Essentially, the tub seal failed & allowed water to travel down the shaft & into the housing containing the bearing. I confirmed this by pulling the front cover off of the unit & noticed some brown water pooled directly under the shaft & tube assembly. I followed the disassembly instructions on this site & it wasn't too bad but did take some time as pretty... Read more

I ordered the parts, after assuring my diagnosis was correct from APP’s knowledgeable representative, and they were shipped quickly. I tipped the washer and disassembled the parts to be replaced and then installed a new clutch, clutch spring and mode shifter. Read more

Remove one bolt in the center of the agitator need a long extension, couldn't be any easier. Read more

I had never worked on a washing machine before but after watching the online videos I felt like I could do the repair. I was almost positive it was the Mode Shifter and Shaft Assembly that was bad. I could hear the bearing making a grinding noise when I turned the tub by hand. I ordered the part I needed plus additional parts that could be an issue later such as a drive belt, tub bearing, tub seal, tub nut, split ring, etc; Preventive maintenance that would keep from having to tear it all... Read more

Ordered a new timer and knob. The husband was able to fix in about 20 minutes and now works like new. Read more