Magic Chef Parts

• Heat stays on after drum has stopped
• Will not tumble
• Touchpad does not respond
• No heat or not enough heat

Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more

• Timer will not advance
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

I'm starting with a quick background on my dryer. About 18 months ago the belt on the dryer started slipping and squealing. I had a can of belt dressing spray so I popped the top open and sprayed the belt. It actually worked for about a year before it started squealing again. For the next 6 months I had to spray it more and more often. Then the clothes stopped drying. Obviously, at this point, I had to get off my lazy ass and fix the dryer. Searched my dryer's model number on the internet and... Read more

• Not drying dishes properly
• Not cleaning dishes properly

My Whirlpool dishwasher (wdf520padm3) started leaving food on dishes and not drying dishes as well as it used to, even when I ran the 'high temp' and 'heavy' cleaning options. This started happening after about 3 years of operation. To try to diagnose the issue, I started the diagnostics cycle (see below for instructions on how to do this). However, the 'Clean' LED is also not working on my dishwasher, so I was unable to read the error code after the service cycle finished. I decided to... Read more

My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep? After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink. A... Read more

• Ice maker dispenses too little ice
• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

My first hour: I investigated first by pulling out refridgerator to see if the water line hose was kinked. I started under the kitchen sink where it begins, coming from faucet water supply. Then I followed it to the back of the fridge to see if anything looked odd. Next I went to the ice maker itself. I investigated the ice maker by removing the freezer food sliding tray and hanging tray, and then unscrewing the door off the slides. When I looked inside at the ice maker, I saw the tube where... Read more

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Will not tumble

I went to the local Home Depot and Lowes, but they did not have the parts because they do not carry parts for the items they actually sell to people. Jumped on the phone and did a quick search for parts and came across appliancepartspros.com. I put in the make and model of my dryer and all the parts for the dryer where listed. I ordered the items on a Wednesday night. I opted for the two day shipping. I thought the items would be at my house by Friday but they did not arrive until Monday. I... Read more

• Little to no heat when baking
• Oven not heating evenly
• Element will not heat

The first thing I did was call appliance pros. The tec told me it was a good chance it was the thermostat. He told how to test it with my ohm meter and what range it should be in. I pulled it out and tested it, which was out of the limits he told me it should be in. So I ordered the part. When it arrived in two days, I installed it. The oven now works perfect. Thank you so much. I was just about to go spend $800 on a new oven, and instead fixed it for $75. Awesome website. It was... Read more

• Shuts off too soon
• No heat or not enough heat
• Takes too long to dry

I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more

After extremely poor support from WhirlpooI and researching numerous U-Tube videos, I fully troubleshot potential failed components and connections. All appeared to function properly, so I reassembled the unit and experienced the same problem as before. I then narrowed down the problem to either the Touchpad ($57+$8 shipping) or the control board ($295+shipping). If those did not work, then a new Microwave of better quality, reliability and support than original microwave, Unfortunately,... Read more

• Noisy
• Door won't close
• Door latch failure

I finally decided to repair my dishwasher because the door would free fall to the floor possibly breaking the hinges. Also the top shelf was rolling out on its own every time the door was opened. I first pulled the dishwasher out of the enclosure and found that the drain hose was directly under the pump area throwing the unit completely out of level. Also the inadequate plastic and rope counterbalance on the left side was completely broken where the rope was attached to the plastic piece to the... Read more

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more

• Frost buildup
• Freezer not defrosting
• Freezer section too warm
• Fridge too warm

Condenser was encased in solid block of ice due to automatic defrost not working. Replaced thermostat and ADC control board. Working fine now. Most tedious part was using a heat gun to melt all the ice off the condenser coils. You will need a couple small wire nuts to splice the new thermostat into the existing harness (they are not included). Service tech wanted over $400 to repair, fixed it myself for half that. Thanks ! Read more

Replaced the water solenoid. Read more

• Leaking

I followed your step by step instructional online video. That is one great tool you are providing for your customers! Read more

• Element will not heat
• Won't start

The receptacle that held the burner element in place was broken so the burner would not make a connection and heat up. I ordered the receptacle kit. There was even an online video that showed how to make the repair. It just took a screwdriver and wire cutters and about 15 minutes and the job was done. The burner works great. Read more