Wtw4957pwo Parts

With the video that was made from appliance pro.Help me out one hundred percent to understand what I was dealing with Read more

Replaced washer drive block and Cam. I called around and finally settled on Appliance Parts Pros because they helped diagnose the problem, told me what parts to replace and had videos to show me how to do it. In completing the repair I had to remove quite a few pieces of hardware in order to get at the part I was to replace. The videos helped but there is a learning curve while you familiarize yourself with the parts and figure out how the remove them. Eventually I got to a large nut that,... Read more

I watched a video on YouTube that showed my exact problem. It had a link to this part AP5665171 Hub and it showed how to fix it. It was a fairly simple fix. I did not even have to remove the tub. I popped the cap on top of the agitator plate (AGP), removed the bolt hold the AGP on. I tapped on the bolt several time to loosen it. Using an angled screw driver, carefully and slowly lifted up the edges of the AGP until I could use my fingers to carefully pull the AGP off the splined drive... Read more

The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more

I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more

The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more

I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more

Replaced suspension rods. Read more

Replaced the Gearcase assembly which is a sealed unit that is not serviceable. Also replaced the clutch and belt because they were covered in gearcase oil. Read more

New control board Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

After not finding the needed parts to extend the hose at home depot, i turned to online help. I was able to find the right parts quickly on your site and was able to even watch a few videos on how to do the repair. I was beyond amazed that the parts arrived the next day, even though a Saturday and even with standard shipping. I was fortunate enough that my repair did not need any real explanation and the job was done in less than 10 minutes. Felt really good to be able to solve the problem,... Read more

Replaced tub seal. It was a big challenge for me since it was the first time I do something like that. It was just a worn-out little seal at the bottom but in order to get to it, I had to dissemble almost the entire machine. I felt pretty good afterward. Read more

I had previously replaced the transmission in my two year old Whirlpool Cabrio washing machine. Overall it was in good shape but gets heavy use. That repair was approximately $200 and worked for several months. Recently it began leaking. At first I thought it was the tub-to-shaft seal. I replaced this part but it was still leaking. It turns out it was the simplest of things... The drain hose was not connected very well! I replaced the drain hose ($11 part) and while I was at it I... Read more

I had to cut the old agitator out with an oscillating saw in order to access the agitator drive. This is the second Maytag (MVWC 565) I have had to do this to. I first tried removing it by sliding straps under the agitator then then using a jack to pull it loose which did not work either time. One suggestion I have would be to remove debris from tub as you cut in order to prevent it from dropping from the inner tub into the outer tub. Read more

Replaced pump Read more