Need Help?
Call
Hex screw fastener for securing lawn mower components. Replace if stripped, rusted, or missing to ensure proper assembly and equipment stability.
Usually ships within 4 - 14 days
Fix a chute that won't rotate properly with this snow thrower chute flange keeper latch. Secures the flange to ensure smooth chute rotation. Easy DIY fix.
This lower chute is a quality replacement part that is used on several models of snowblowers. It is made of high-quality plastic for durability and is placed so it can direct snow in a certain direction when it leaves a snowblower. Over time and with regular use, this part can become damaged. If this occurs, it will need to be replaced so the discharged snow ends up in the right location.When replacing the lower chute, a wrench and work gloves will be needed. The snowblower should be placed on a flat surface, and the spark plug wire needs to be disconnected. The gearbox and the lower chute will need to be removed before the new replacement part can be installed. Line up the chute and install it used the cotter pin and flange lock nut. Replace all the components before using the snowblower.This is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold on an individual basis. The lower chute is used with snowblowers manufactured by Craftsman, Cub Cadet, Huskee, MTD, Troy-Bilt, Yard Machines, and Yard-Man.
Replaced the lower chute. Read more
Bell washer adds spacing on shafts in lawn tractors, tillers, mowers, and chipper shredders. Replace if washer is missing, worn, or damaged during maintenance.
Throttle control won't adjust engine speed or feels sticky? This throttle control box restores smooth speed regulation on lawn tractors and tillers.
Black plastic wheel hub cap for lawn tractors and riding mowers. Replaces cracked, broken, or missing hub caps. Snaps onto wheel hub for a finished look.
Ordered parts and they were an exact fit easy fix. Read more
Auger bearing flange connects to the bearing to reduce friction during operation. Replace if worn or damaged to restore smooth auger rotation. Verify fit.
Replacement drive control cable for gas snow throwers. Connects handle control to engine drive system. Replace if cable is frayed, damaged, or broken.
Seals between carburetor and engine block to prevent air and fuel leaks. Replace if engine runs rough, leaks gas, or loses power. Verify fit by model.
Fix snow thrower auger that won't turn or spins slowly with a new auger belt. This rubber V-belt drives the auger rotation on two-stage models.
This is a dual cable fitting, designed to work with snowblowers. The cable fitting holds the auger cable in place, ensuring that it does not become a safety issue. The cable simply runs through the fitting, and the part holds it in place. Cable fittings are made from durable plastic and are not moving parts. However, they can suffer damage in several different ways. Plastic becomes brittle over time and through exposure to the elements, and the fitting may eventually crack and break. It is also possible to damage the fitting through contact with a hard surface while using the snowblower. Replacing a dual cable fitting is not difficult, although it will require a socket set. Locate the fitting on the handle of the snowblower and remove the mounting bolt(s). Remove the fitting and replace it with the new one. Be careful that the cables are properly routed inside the new fitting, then replace the mounting bolt(s). This is a genuine OEM part, and it is sold individually. This dual cable fitting is compatible with Craftsman, MTD, and Yard Machine snow blowers.
I ordered the replacement part. It left Bartlett Tn 11-6-2018. It arrived at my door 11-16-2018 after traveling half way around the country. It took less than 10 min. to put the part on the machine. Read more
Extension spring that mounts the drive plate assembly to the housing frame on snowblowers. Replace if broken, stretched, or missing for secure mounting.
Shoulder spacer for lawn tractors and riding mowers. Installs to maintain proper spacing between components. Replace if worn, damaged, or missing.
Snowblower not clearing snow properly? Worn rubber paddles reduce snow removal efficiency. This auger paddle kit restores clearing power in about 30 minutes.
Replaced them Read more
This part is an idler pulley. The idler pulley applies tension to and guides the engine drive belt. A wrench set is needed to perform any repair involving the idler pulley part.The idler pulley can become worn over time with normal use. Wear to the pulley can cause the belt to slip. Signs that the idler pulley needs to be replaced include squealing noises coming from the equipment, the engine stalling, or overheating. The idler pulley is an essential component and it is important to replace this part if it becomes worn, broken, or damaged in any way.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer and it is sold individually. This idler pulley is compatible with lawn tractors and snowblowers manufactured by MTD, Yard Machines, Bolens, Yard-Man, Troy-Bilt, Cub Cadet, and Husky.
30-inch shave plate blade for snow throwers. Installs at the auger housing base to protect surfaces. Replace when worn, cracked, or damaged.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.