Parts for Frigidaire FFHS2622MSA: 13 - System Parts

Replace your refrigerator water filter every 6 months to maintain fresh-tasting water and remove impurities like lead and chlorine. Confirm fit by model.

Refrigerator not cooling properly? A damaged or clogged condenser coil prevents heat rejection, causing warm temps. This assembly restores efficient cooling.

Foam insulation block that surrounds the evaporator coil in your refrigerator. Replace if melted, cracked, or missing to maintain proper airflow.

Includes service line.

The Wiring Harness is an OEM part for Frigidaire refrigerators. As the complex network distributes power throughout the cabinet, this harness is crucial for seamless communication between electrical parts. Its bundled cables provide synchronized functi

The Defrost Heater is an OEM part for Frigidaire refrigerators. It plays a crucial role in the refrigerator's defrost cycle, melting away any frost that accumulates on the evaporator coils.

Causes of a bad Defrost Heater can include a burnt

Refrigerator not cooling or freezing properly? A faulty evaporator coil may be causing warm temps and moisture buildup. Professional installation recommended.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Freezer icing up or fridge not cooling? This defrost thermostat kit fixes refrigerators that won't defrost properly. 10-minute DIY repair with video.

Fix refrigerator not cooling or running constantly with this compressor base. Common repair for side-by-side models. Moderate difficulty installation.

Rubber grommet that mounts and cushions the compressor to reduce vibration transfer. Replace if cracked, worn, or missing to restore quiet operation.

Secures the compressor to the mounting bracket in your refrigerator or freezer. Replace if missing, stripped, or corroded during compressor service.

Collects water from evaporator defrost cycles. Mounts near compressor under refrigerator. Replace if cracked, leaking, or damaged to prevent odors.

Fridge not cooling or making loud buzzing noise? This compressor kit restores cooling in refrigerators and freezers. Professional repair recommended.

Compressor won't start or rattles? This start relay enables the compressor to begin the refrigeration cycle. DIY-friendly repair, typically done in under an hour.

Secures refrigerator hoses and tubing to fittings to prevent leaks. Replace if connections are loose or water is dripping. Verify fit with your model.

Black rubber mounting grommet that secures tubes and wires in your refrigerator. Replace if cracked, worn, or missing to properly hold components in place.

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread

Secures and protects wiring harness from strain damage. Replace if cracked, broken, or wires show wear. Verify fit with your model number listed.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Compressor clicks and won't start? Run capacitor helps start and run the compressor motor. Most DIYers replace in under 15 minutes with basic tools.

Replacement mounting screw secures panels, brackets, and trim inside refrigerators and freezers. Restores factory assembly when original fasteners are missing.

Positions the condenser fan and motor in the rear machine compartment. Replace if cracked, warped, or damaged to restore proper airflow direction.

Refrigerator not cooling or making loud grinding noise? The condenser fan motor drives airflow to cool refrigerant. DIY repair in 30-60 minutes.

Refrigerator not cooling properly? A damaged condenser fan blade prevents airflow over the condenser coils. Quick DIY fix—simply push into place.

Channels defrost water from the evaporator to the drain pan. Replace if cracked, broken, or leaking water into the freezer compartment or onto the floor.

Secures the evaporator cover inside your refrigerator's freezer compartment. Replace this metal bracket if bent, broken, or missing to restore alignment.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Routes defrost water from the freezer evaporator to the drain pan. Replace if cracked, split, or clogged to prevent leaks under your refrigerator.

Positions and secures condenser tubing to maintain proper spacing. Replace if worn, broken, or missing to prevent vibration, rattling, and tube damage.

Foam seal tape creates airtight barriers around refrigerator components. Replace when worn, compressed, or damaged to restore proper sealing and efficiency.

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.