Parts for Whirlpool WFW97HEXL2: 01 - Top And Cabinet Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This top panel is the exterior upper cover that protects internal washer parts and gives the appliance a finished look. It restores a secure mounting surface for the control area and helps keep water and debris out of the cabinet. What it does

• Covers and protects internal components at the top of the washer cabinet.
• Provides the mounting surface and alignment for the control console and lid.
• Restores appearance when the original panel is dented, cracked, or rusted.
• Reduces rattles or vibration caused by a loose or warped top.

• Disconnect power and water supply before starting any repair.
• Use basic hand tools; some screws or clips may need to be removed to lift the old panel.
• Handle edges carefully — metal panels can be sharp.
• Have a second person assist if needed to prevent bending or dropping the panel.

This front panel assembly replaces a cracked, faded or damaged control panel and restores the appliance's appearance and function. It provides the mounting surface for controls and helps protect internal electronics from everyday wear. What it does:

• Houses and secures the control buttons/knobs and display area
• Protects underlying electronics from dust, spills and impact
• Restores a flush, finished look to the appliance front
• Helps resolve issues where the exterior panel is cracked, warped or cosmetically worn

• Disconnect power to the appliance before attempting any repair.
• Handle the panel carefully to avoid scratching or bending; some fasteners clip into place.
• Some disassembly of the console or trim may be required; keep track of screws and clips.

The Outer Door Boot Seal Clamp Washer is an OEM replacement part specific to Whirlpool-brand washing machines. Multiple washers are used behind the outer boot seal clamp to create a uniform, compressed seal around the washer door opening. 

Symptoms of worn or damaged clamp washers include:

• Water leaks occurring around the outer door seal 
• The door not sitting flush or sealing tightly when closed
• Water intrusion indicated by interior mold/mildew buildup

Causes may involve deterioration of clamp washer material over extended washing machine use cycles. Washers crack or fail to adequately cushion and compress the door seal.

The part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Door Latch Assembly is an OEM part for Whirlpool washing machines. This assembly secures the washer door during operation, ensuring it remains closed and the washer operates safely. It also signals the washer to begin the wash cycle when the door is properly latched.

Over time, door latch assemblies can wear out or become damaged due to frequent use, exposure to moisture, or accidental impacts. A faulty latch may prevent the washer from starting or cause it to stop mid-cycle.

Symptoms of a bad door latch assembly include:

• The washer not starting or responding
• The door not locking or unlocking properly
• Error codes related to door latch issues
• The washer stopping mid-cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

This expansion control board is an electronic assembly that adds or restores control functions by communicating with the main control board. It helps return specific dispenser/feature or subsystem control when the expansion board is faulty. What it does:

• Interfaces with the washer/dryer/refrigerator main control to manage added functions or subsystems
• Can cause feature loss or unresponsive subsystem controls when failed
• May trigger related error codes or prevent certain cycles/features from operating
• Restores electronic communication for the tied subsystem when replaced

• Disconnect power to the appliance before servicing to avoid shock or damage
• Handle the board by edges and avoid touching contacts; observe electrostatic-discharge (ESD) precautions
• Transfer any required brackets, shields, or wire harnesses exactly as removed; keep fasteners organized

The Motor Control Board is an OEM part for Whirlpool washing machines. This electronic board is responsible for regulating and controlling the motor's speed and direction during various cycles, ensuring optimal washing performance.

Over time, the motor control board can fail due to electrical issues, power surges, or general wear and tear. When the control board malfunctions, it can disrupt the washing machine's operation and lead to various performance issues.

Symptoms of a bad motor control board include:

• The washer not spinning or agitating
• Erratic or unpredictable cycle times
• The washer stopping mid-cycle
• Error codes related to motor function

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Shipping Bolt Kit is an OEM part for Whirlpool washing machines, specifically designed to secure the appliance during transport. This kit includes several bolts that are crucial for immobilizing the washing machine's drum, preventing any movement that could lead to internal damage while the unit is being moved. This kit includes two front and two rear shipping bolts

Causes for replacing the Shipping Bolt Kit can stem from misplacing the original bolts after installation or the bolts becoming worn or damaged after multiple uses.

Symptoms of needing a Shipping Bolt Kit include:

• Preparing a washing machine for a move without the original bolts, risking damage to the unit
• Noticing previous shipping bolts are lost or damaged, requiring replacement for future transport

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

This small replacement clip secures a press (push) switch to the appliance control panel so the switch stays aligned and operates reliably. It restores proper button engagement and prevents the switch from working loose. What it does:

• Holds the press/push switch firmly in the control panel or console
• Keeps the switch aligned so button presses register correctly
• Helps stop intermittent or loose-feeling buttons caused by a failing retainer
• Prevents the switch from shifting or falling out during use

• Disconnect power before starting any repair to avoid shock or injury
• Access typically requires removing the control panel or console—retain screws and note their locations
• Clip installs by snapping into the panel and seating the switch; small pliers may help with alignment

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This RFI noise filter conditions the AC power entering your microwave, reducing electrical interference and helping protect and stabilize the control and power circuits. Replace it if the unit is dead or trips a breaker when starting.

• Filters radio-frequency/electromagnetic noise on the incoming AC line
• Helps stabilize power to the control, relays, lights, and fans
• Failure may cause no display or intermittent loss of power
• A shorted filter may blow the line fuse or trip the household breaker when plugged in or when Start is pressed

• Disconnect power by unplugging the microwave or switching off the dedicated circuit breaker
• For over-the-range units, remove the microwave from the wall to safely access internal components
• Label and transfer wires to matching terminals; mount the filter securely and route wiring away from sharp edges

This water level pressure switch senses the washer's water height and tells the control when to stop filling, helping maintain correct fill levels for normal wash cycles. It replaces a failed or intermittent pressure sensing switch. What it does:

• Detects water level via the air/pressure tube and signals the washer control to stop filling.
• Can prevent overfilling or underfilling when functioning correctly.
• Common symptoms it can address: washer overfills, won't fill to the correct level, or cycles incorrectly due to incorrect level sensing.
• Works as the electrical/mechanical switch that communicates water pressure information to the control board.

• One water level pressure switch

• Disconnect power and turn off the water supply before installing.
• Verify and reconnect the air/pressure tube securely; replace tube if cracked or clogged.
• Handle electrical connectors carefully; ensure proper seating and strain relief.

The Pressure Switch Hose is an OEM part for Whirlpool washing machines. This hose connects the pressure switch to the washer tub, allowing the machine to detect water levels and ensure proper operation of the washing cycle.

Common causes of damage include cracks, holes, or clogs in the hose, which can occur due to wear and tear, exposure to harsh detergents, or foreign objects in the washing machine. 

Symptoms of a bad pressure switch hose include:

• The washing machine not filling properly
• Overfilling or underfilling of water
• Error codes related to water levels
• The washer not advancing through cycles correctly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This retainer is a small mounting clip that secures internal components in place to prevent shifting and noise during operation. It restores proper alignment so panels or assemblies stay fastened and stable. What it does

• Holds a panel, trim, or internal component securely in its mounting location
• Prevents rattling, vibration noise, and loose or sagging parts
• Keeps connected parts aligned for reliable operation
• Commonly replaced when clip is cracked, broken, or missing

• One retainer clip

• Disconnect power before starting any repair
• Remove necessary panels or access covers to reach the damaged clip
• Replace the clip in the same orientation; avoid forcing parts to prevent damage
• If additional fasteners are damaged or missing, replace them as needed for a secure installation

This mounting bracket secures panels or components in place to keep your appliance stable and aligned for reliable operation. It's a simple replacement that restores proper support and reduces rattling or movement. What it does

• Provides a secure mounting point for a panel, assembly, or component
• Keeps parts aligned to prevent vibration and noise during operation
• Restores structural support if the original bracket is bent, cracked, or broken
• Helps maintain correct clearances so adjacent parts operate smoothly

• One mounting bracket

• Disconnect power (and water, if applicable) before beginning any repair
• Use proper hand tools; avoid overtightening fasteners to prevent damage

The Spring Tension Hose Clamp is an OEM part for Whirlpool washing machines. It is designed to secure hoses in place, preventing leaks by maintaining consistent tension on the hose connections.

Over time, spring tension hose clamps can lose their effectiveness due to metal fatigue, corrosion, or damage from frequent tightening and loosening. This can lead to leaks and improper hose connections.

Symptoms of a bad spring tension hose clamp include:

• Water leaks around hose connections
• Loose or disconnected hoses
• Unusual noises or vibrations during operation
• Water pressure issues within the washing machine

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

The Drain Hose is an OEM replacement part for Whirlpool washing machines. Located at the rear base of the unit, this flexible vinyl hose routes wash water out of the tub and to household drainage pipes.

Causes involve regular flexing weakening hose material integrity over many years. Mineral buildups may also restrict water flow within.

Symptoms of a problematic drain hose include:

• Puddles or residual water remaining after cycles
• Slow drainage of water not meeting cycle timers
• Hose material cracks or splits exposing reinforcement

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This genuine replacement power cord restores electrical connection to your appliance so it can safely receive power. It replaces a damaged or worn cord to help eliminate power loss and reduce electrical hazards. What it does:

• Provides the electrical connection between the appliance and your home's power supply
• Replaces frayed, cracked, or burned cord insulation and damaged plugs
• Helps stop intermittent power issues caused by a faulty cord or connector
• Restores safe, reliable power routing when the original cord is compromised

• Always disconnect power at the breaker or unplug the appliance before installing
• Follow the appliance wiring diagram and route the cord to avoid heat or pinch points
• Secure strain relief and connectors per the manufacturer's instructions

Size: 10-24 x 3/8 inch.

This transport cover secures internal components during shipping and service to prevent movement and damage. It helps keep parts aligned and reduces noise caused by loose components while the appliance is being moved. What it does:

• Holds internal components in place during transport to prevent shifting or impact damage
• Reduces rattles and vibration caused by unsecured parts
• Protects delicate assemblies from knocks during delivery or handling
• Helps maintain alignment of components until the appliance is installed

• One transport cover

• Disconnect power and water before servicing the appliance
• Remove all shipping brackets and covers per the owner's manual before normal operation
• Use manufacturer-specified fasteners and torque; do not force or modify the part

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

The Front Leveling Foot is an OEM part for Whirlpool washing machines. It is designed to support and stabilize the washer by allowing users to adjust the height and level the appliance on uneven floors. Proper leveling ensures smooth operation and minimizes vibrations and noise during wash cycles.

Causes of a bad Front Leveling Foot can include physical damage from excessive force, wear and tear from frequent adjustments, or corrosion due to exposure to water or laundry chemicals. Over time, these factors can compromise the foot’s ability to maintain stability, leading to operational issues.

Symptoms of a bad Front Leveling Foot include:

• The washing machine rocking or wobbling during operation
• Increased vibration and noise
• The washer being unlevel, affecting wash performance
• Difficulty in adjusting the foot

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.