Wall Oven Latch, Catch, Lock Parts

This lid switch actuator engages the washer's safety switch when the lid is closed so cycles can start and spin as designed. Replace a broken or missing actuator to restore proper lid switch engagement and reliable operation.

• Engages the lid switch when the lid is closed to enable agitation and spin
• A worn, cracked, or missing actuator can cause the washer not to start or to stop before spin
• Intermittent operation that changes when pressing on the lid often indicates misalignment
• Lack of an audible "click" from the lid switch can point to a faulty actuator or alignment

• Disconnect power before servicing; do not work on a live appliance
• Access the lid/switch area per your model's service procedure
• Remove the damaged actuator and install the new part, securing as designed
• Before reassembly, close the lid to ensure the switch clicks and engages properly

This motor drives the fan or mechanism in your cooking appliance to move air as designed. Replacing a worn or seized motor restores proper airflow and quieter operation for consistent baking, cooling, or venting performance, depending on model.

• Powers the appliance's fan or drive to circulate air or move exhaust
• Helps maintain even temperatures or ventilation during operation
• Replaces a noisy, slow, or non-spinning motor
• Common signs: fan won't run, weak airflow, humming/grinding noise, overheating, or a tripped breaker

• Disconnect power at the breaker; shut off gas supply for gas models
• Access location varies by model; remove the necessary panels to reach the motor
• Note wiring and rotation; transfer any brackets, grommets, or the fan blade from the original, if required
• After installation, verify smooth, quiet operation and correct airflow

This door latch secures the appliance door and signals the control that it's safely closed. Replacing a worn or broken latch restores reliable door closure and proper cycle operation. What it does:

• Holds the door closed and aligned during use
• Engages the door strike to complete the door/lock switch circuit
• Resolve issues such as: door won't latch or pops open; cycles won't start; intermittent "door open" messages; needing to press/hold the door to run

• One door latch

• Disconnect power before servicing
• Access is typically from the door/front panel; note screw locations and latch orientation
• Transfer any mounting hardware from the original latch if needed
• After installation, verify smooth latch engagement with the strike and run a test cycle

Replacement motor that restores mechanical drive or airflow in select Frigidaire appliances. Installs in place of the original motor to help return normal rotation, tumbling or fan operation. What it does:

• Drives rotating components (drum, tumbler, agitator or fan) depending on application.
• Helps restore normal spin, tumble or airflow when the original motor fails.
• Common symptoms: appliance won't start or spin, weak/uneven rotation, loud humming/grinding, or reduced airflow.
• Direct-fit replacement designed to match original mounting and electrical connections for specified models.

• Disconnect power (and water if applicable) before beginning any work.
• Avoid pulling on wires; reconnect all harnesses and secure mounting fasteners per OEM instructions.

This latch and tape assembly restores proper door engagement on compatible ovens/ranges so the door closes and locks as designed. It helps ensure safe operation and consistent temperatures by keeping the door secured during cooking and, on applicable models, self-clean cycles.

• Provides the mechanical catch that engages the door strike
• Helps keep the door closed; supports door-lock function on models equipped with a lock
• A worn or bent latch can cause the door not to close fully or pop open

• Disconnect power; for gas ranges also shut off gas supply
• Access location varies by model; expect to remove panels/trim to reach the latch area
• Transfer/reuse mounting hardware; align latch to ensure smooth door engagement
• After installation, verify door closes and locks properly before restoring power

This rear latch assembly secures the dryer door so the appliance can latch and run properly. It replaces a worn or broken rear latch to restore reliable door closure and help the dryer start and stay closed during cycles. What it does:

• Secures the dryer door to engage the door switch so the dryer will start
• Keeps the door closed during operation to prevent interruptions mid-cycle
• Replaces a broken, bent, or worn latch that prevents the door from latching
• Commonly used when the dryer won't start, stops unexpectedly, or the door won't stay closed

• Disconnect power (unplug or switch off breaker) before beginning any work
• Installation may require removing the dryer top or front panel; follow the model's service instructions
• Handle panels and metal edges carefully to avoid cuts
• After installation, verify the door latches securely and the dryer starts before reassembling all panels

This door opening lever is the replacement release lever that lets the appliance door latch open and close smoothly, restoring reliable door-opening action and making everyday use easier. What it does:

• Replaces a worn, broken, or cracked lever that releases the door latch.
• Lets the door latch release properly so the door opens without excessive force or sticking.
• Works with the latch assembly to help ensure the door closes securely and operates smoothly.
• Addresses common symptoms such as a loose or unresponsive door handle, difficulty opening the door, or a lever that snaps.

• Disconnect power (and water, if applicable) before attempting any repair.
• Access may require removing the door trim or outer panel; basic hand tools are typically needed.
• Inspect surrounding latch components while replacing the lever and replace any damaged hardware.

This oven door latch assembly secures the door and communicates lock status to the control. Replacing a worn or jammed latch restores safe door locking so bake and self-clean cycles can start and finish correctly.

• Locks and unlocks the oven door when engaged or commanded by the control
• Secures the door during the self-clean cycle for safety
• Helps resolve issues such as a door that won't lock or unlock, self-clean that won't start/finish, or a persistent "door locked" indicator
• Wear, binding, or internal failure can prevent proper latching

• Disconnect power at the breaker before servicing
• Access location varies by model; typically serviced from the top, rear, or control/console area—follow your model's service procedures
• Transfer any mounting hardware and reconnect wire harnesses one at a time
• After installation, verify smooth latch movement and door locking before running a cycle

A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:

• Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
• Reduces vibration and rattling during operation
• Helps doors and panels sit properly when closed
• Simple, non-electrical part — no wiring or adjustment required

• One replacement bumper

• Inspect the mounting hole or surface; clean debris before installing
• Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
• Disconnect power to the appliance first and follow OEM instructions
• Remove old adhesive before installing the new bumper

The Latch is an OEM replacement part for Frigidaire built-in microwaves. Securely mounted to the top interior section of the microwave cavity door, the positive-locking latch holds the door safely shut during operation. Crafted from corrosion-resistant materials for extended use, the latch handle withdraws the hook mechanism with a simple pull to conveniently access food within.

Symptoms of a bad latch include:

• The microwave door popping or falling open unexpectedly  
• Difficulty closing or fully engaging the secure latch hook 
• Wear signs like loose mounting points or a worn handle

Causes can involve repeated opening/closing cycles gradually loosening mounting fixtures, or parts rendered ineffective by moisture intrusion over time.

Replacing this Frigidaire OEM latch prevents potential microwave door opening during cooking cycles. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore built-in models.

This replacement latch assembly secures the refrigerator or freezer door to ensure proper closure and reliable operation. It restores the door catch so the appliance can maintain an effective seal and help prevent cooling loss. What it does:

• Secures the door to keep it closed and aligned
• Replaces a broken, bent, or worn latch that prevents proper latching
• Helps reduce warm air entry caused by a door that won't stay shut
• Works as the mechanical catch that engages the door striker

• Disconnect power (unplug appliance) before servicing to avoid shock or injury.
• Remove the inner door panel or access trim as needed to reach the latch; keep screws and fasteners organized.
• Align the latch with the door striker and tighten screws securely without over-torquing.
• Test door operation several times after installation to ensure proper engagement and seal.

Replacement latch keeper for the dryer door latch assembly that secures the latch and keeps the door closed during operation. Restores reliable door engagement to help the appliance start and complete cycles. What it does:

• Secures the door latch so the dryer door stays closed during operation.
• Aligns with the latch mechanism to maintain proper door engagement.
• Common symptom: dryer door won't latch or feels loose, causing the cycle to not start or stop unexpectedly.
• Replaces worn or broken keeper pieces that allow rattling or misalignment.

• Disconnect power (unplug electric or shut off gas and breaker) before servicing.
• Access with basic hand tools; remove the door or front panel as needed to reach the keeper.
• Install carefully to avoid cracking surrounding plastic; do not force parts into place.
• After installation, verify the door closes securely and the dryer starts through a test cycle.

This latch and harness assembly secures the appliance door and sends the closure signal to the control, restoring proper door operation and allowing the unit to start or run normally. What it does:

• Replaces a worn or broken door latch and its wiring harness so the door closes and stays latched.
• Restores the electrical connection that detects door-closed status so the appliance can begin its cycle.
• Commonly used when the door will not latch, the appliance won't start, or the door switch isn't being engaged.
• Fits the original mounting and wiring locations for a direct-replacement installation.

• One latch and harness assembly.

• Disconnect power (unplug or switch off breaker) before starting any repairs.
• Basic hand tools are typically required; handle metal edges and sharp tabs with care.
• Verify correct alignment of the latch and secure all fasteners; test door closure and operation before full reassembly.