Whirlpool Cooktop Parts

Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site. Read more

• Door won't close

For the third time in four years, the hinges failed on my KitchenAid wall oven. The appliance is out of warranty and KitchenAid does not consider this to be worthy of any recall. I was tired of paying the appliance repairman to change out the hinges, so I ordered the part online. Appliance Parts Pros is an awesome site for identifying the part you need, and they deliver quickly. Note that you probably need TWO hinges--they do not come as a set--and KitchenAid likes to make their model numbers... Read more

Bought a Thermador PRSE48" dual fuel range from Craigslist really cheap because it didn't work. Did a little research and decided to overhaul most of the top (gas) end. For what I paid for it it was worth it and I'd have a good stove with new components. Replaced the griddle thermostat, ignition micro switches, ignition re-igniter box, installed fixing kit with 2 new potentiometers, both solenoids, and gas regulator. Had to replace 2 gas lines, all 4 jets, and one brass nut that were... Read more

Oven part was hard to fix as space was very small, it took longer than even you tube video said it would Read more

After cleaning our stove top, a couple of the grate pads had fallen off the bottom and went down the drain. The pots now rocked while cooking, and not in a good way. I ordered replacement pads installed them and now the only rocking is my cooking. I have used appliancepartspros.com a few times over the years, and ALWAYS get the correct part the first time, and reasonably priced. Read more

• Element will not heat

I ordered 2 bake elements and bulbs and was able to easily fix 1 of the ovens. The serviceman who repaired the left oven did not repair it correctly so, one of the wires was not accessible so, I could only fix one oven. After shutting off the power, I EASILY fixed the right oven - with a LOT of care and a little elbow grease - in disconnecting the broken element, by doing exactly as it said to in the video, making certain not to allow the wires to slip back into the hole that it was pulled... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light

Called a repairman and he told us we needed to change a bunch of parts and would cost over $400! Decided to do some research online and found suggestions to replace the spark igniter. Decided to give it a try. Took about 10min to replace and oven is now working perfectly, for a total of $30! Read more

Just took out the old ones and replaced with new ones. Read more

Replaced dual element switch. Fixed the problem. All is good Read more

The plastic piece on the handle where the screw goes in to hold glass door up had broke. I ordered new handle, the retainer pieces that go over the plastic pieces to lock it all in and screws that were suggested. The screws were the wrong ones. They were way too small. I already had one screw and thankfully only had to buy 1 new one because the screw was $40 and shipping’s $10 for it AND it’s on back order right now. The old retainer ring that goes over plastic piece was a nightmare to remove... Read more

Replaced burners, saved $350, easy and it worked! Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

Installed it according to video watched. Read more

Had to replace the switch for the left rear burner on a Whirlpool cooktop Model W5CE3625AB00. I turned off the circuit breaker for the cooktop and lifted it out of the countertop. It was simply held down by its own weight. There were approximately a dozen screws holding the smooth surface down onto the rest of the unit. I removed those screws, which allowed the cooking surface to lift back on a hinge in the back of the unit. Two of those screws were stripped, but I was able to remove them... Read more

We replaced both front orifice holders. Very easy to bend and break. If it has a deep bend in it, It will slow down the gas flow to the burner. if you have a low gas flow your burner will burn low So check your small silver gas lines and if you smell gas check your lines Read more