Whirlpool Dryer Parts

Replaces the cabinet back panel on your dryer. Needed when the original is cracked, damaged, or missing. Covers internal components and restores enclosure.

Adjustable periscope vent for tight dryer installations. Extends 18-29 inches to connect 4-inch dryer vent to wall exhaust in close quarters.

This drum hole plug seals an unused or service access hole in the dryer drum to help prevent clothing snags and reduce interior airflow leaks. Simple replacement restores the drum surface and helps keep items from catching. What it does:

• Covers a drum access/service hole to provide a smooth interior surface
• Prevents fabric from catching or tearing on open drum holes
• Reduces unwanted air leakage through the drum
• Helps maintain normal drum rotation contact points by keeping openings closed

• One drum hole plug

• Disconnect power to the appliance before starting any repairs
• Inspect the drum area and remove any debris before installing the plug
• Press or snap the plug into the hole until fully seated; replace if damaged or deformed

Touch-up paint kit for dryers and washers. Restores painted finish on chipped, scratched, or scuffed surfaces. Blends repaired areas seamlessly.

Wire harness assembly that routes power and signals between dryer components. Replace if damaged, frayed, or causing intermittent electrical faults.

Front bulkhead panel that supports the dryer drum and seals the cabinet. Replace if cracked, warped, or damaged to restore drum alignment and airflow.

Fix a dryer that won't heat or overheats with this temperature-sensing thermostat. Controls heating cycles for proper drying. DIY-friendly repair.

This electromechanical timer controls the appliance's cycle sequencing so wash/dry cycles advance and complete as expected. Replacing a faulty timer restores proper cycle timing and program changes for consistent operation. What it does:

• Advances and times cycle steps so selected programs run in the correct order
• Interfaces with selector and motor to start, stop, and change cycles
• Can fail and cause symptoms like cycles not advancing, no power to cycles, or stuck on one setting
• Works with the appliance's existing wiring and mounts in the original timer location

• One electromechanical timer

• Disconnect power before starting any repair to avoid electric shock
• Access may require removing the console or control panel; keep fasteners organized
• Note wire locations or take a photo before disconnecting connectors for correct reassembly

The Bulkhead is an OEM component for Whirlpool dryers. As a structural panel, it secures the rear of the appliance while enabling airflow behind sliding doors. 

Formed from durable composite, the lightweight bulkhead installs easily into precise slotted tracks inside the chassis. This allows full retraction during maintenance without removing additional panels. 

Causes of a faulty bulkhead can include cracked welds or screws stripping their anchors from extreme force vibration over many years of use.

Causes of a bad bulkhead can include:

• Noisy rattling and resonance as the dryer operates  
• Restricted door movement from misalignment
• Inability to fully access internal components  
• Excessive ducting leaks from gasket compression failure

Replace yours with this genuine Whirlpool bulkhead to restore smooth, tight operation. Compatible with Kenmore, Maytag, and KitchenAid dryers.

Color: Citrine white. Size: 0.6 fl.oz. Bottle with brush.

Dryer won't heat or overheats? This thermostat regulates temperature during drying cycles. Easy 15-minute DIY fix restores proper heat control.

This 1/4-20 bolt secures appliance panels, brackets, and components to keep assemblies stable and aligned. It's a direct-fit fastener used where a standard 1/4-20 machine screw is required. What it does:

• Fastens panels, mounting brackets, and internal components to the appliance frame
• Prevents parts from shifting, vibrating, or producing rattling noises
• Restores proper alignment for components that won't sit flush or move under load
• Replaces corroded, stripped, or missing hardware that can cause loose assemblies

• One 1/4-20 bolt

• Disconnect power to the appliance before performing any repairs
• Use the correct socket or wrench for a secure fit; avoid rounded fasteners
• Tighten snugly but avoid over-torquing to prevent thread damage or stripped holes
• Ensure mating threads are clean and free of debris

Fixes intermittent dryer operation or power loss. This wire connector restores secure electrical connections in your gas dryer's control circuit.

Control panel for dryers and laundry centers. Replaces cracked, broken, or damaged panels on the front of your unit. Restores appearance and function.

Replacement mounting screw for securing appliance panels, trim, and internal components. Restores proper fastening when original screws are missing or stripped.