Whirlpool Range / Cooktop / Oven Parts

• Noisy

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

First temp probe,then control board Read more

If one control starts to fail the rest are sure to follow soon - so I replaced all four on our JennAir S160. Looked up the parts on line. Due to my background as an aviation electrician in the Navy and then working as an electrical systems designer for a defense contractor the toughest part was the clean up. Oh Well. Read more

• Gas igniter glows, but will not light
• Little to no heat when baking
• Won't start

Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more

I ordered both hinges (if the nylon roller was bad on the left, it was probably going to go bad on the right side as well). The web site was easy to navigate, order process simple. Hinges arrived quickly. Slide the oven door up and off. unscrew the three screws for the hinge. You need to then pull up with some force (there is a big spring in there), and twist the hinge to get the last bit out. I used a hemostat to hold the spring and keep it from falling back into the hole. removed the... Read more

Bought a replacement gasket. Read more

We bought replacements which fit very well and the burner elements are level again! Read more

Had to replace the switch for the left rear burner on a Whirlpool cooktop Model W5CE3625AB00. I turned off the circuit breaker for the cooktop and lifted it out of the countertop. It was simply held down by its own weight. There were approximately a dozen screws holding the smooth surface down onto the rest of the unit. I removed those screws, which allowed the cooking surface to lift back on a hinge in the back of the unit. Two of those screws were stripped, but I was able to remove them... Read more

By ordering my parts and they fit good. Read more

I replaced the bake element in the bottom of the unit. Read more

I did research on my own prior to ordering. I looked at other sites, but was impressed with the online chatting-this was very helpful! I ordered three items and had difficulty with one rack. I called customer service and received a new rack the next day. This was meaningful to me because we were heading back home in a few days. The rep was very understanding to my situation and helpful. Read more

I ordered a new one Read more

• Door won't close

I ordered both hinges (if the nylon roller was bad on the left, it was probably going to go bad on the right side as well). The web site was easy to navigate, order process simple. Hinges arrived quickly. Slide the oven door up and off. unscrew the three screws for the hinge. You need to then pull up with some force (there is a big spring in there), and twist the hinge to get the last bit out. I used a hemostat to hold the spring and keep it from falling back into the hole. removed the... Read more

• Little to no heat when broiling
• Element will not heat

Replaced it. Read more

These drip pans fit! I had bought some from a local big box store and they didn't fit. I only wish they still made them without the holes in the bottom of the drip pan. How's that supposed to hold a boil-over? But that's the manufacturer. AppliancePartsPros have always sent me orders right on time. Read more