Whirlpool Washer Bearing Parts

The Bearing and Tub Seal Kit is an OEM part for Whirlpool washing machines. It includes high-quality bearings and a tub seal designed to ensure smooth operation and prevent water leaks. The bearings allow the tub to spin freely and quietly, while the seal protects the bearings from water and detergent, extending their life and the overall efficiency of the washing machine.

Causes of failure for these components can vary but often include water infiltration that leads to rust and deterioration of the bearings, or wear and tear from heavy or unbalanced loads that put additional stress on the seal and bearings. 

Symptoms of a bad bearing and tub seal kit include:

• Noisy operation, especially during the spin cycle
• Water leaking from the bottom of the washer
• The washing machine tub struggling to spin or not spinning at all

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Bearing and Seal Kit is an OEM component for Whirlpool and KitchenAid front-load washing machines. The kit includes 2 center post bearings, 3 agitator shaft seals, and 1 center post seal.

These internal seals help retain lubrication inside the motor shaft housing, while the bearings allow for smooth rotation of critical components like the drive pulley. Continuous belt rubbing and water exposure diminish their lifespan over time.

Symptoms of worn motor seals or bearings include:

• Abnormal vibrations during the wash or spin cycles
• Noisy operation and grinding sounds from the motor
• Difficulty starting or stopping the cycle

This OEM kit is also compatible with Maytag, Jenn-Air, Magic Chef, and select Kenmore models.

The Spin Tube Bearing is an OEM replacement part for Whirlpool washing machines. It is a stationary bearing located inside the tub that supports the agitator and spin basket during operation. The bearing works to reduce friction and facilitate smooth spinning motion.

Symptoms of a bad spin tube bearing include:

• Excessive vibration or noise during the spin cycle
• The agitator or basket wobbling noticeably
• Difficulty Balancing loads
• Premature wear of other components

Causes of a bad bearing can include wear and tear due to repeated use over time, damage from cleaning products or foreign objects inside the tub, or improper handling during repairs.

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This small hardware washer sits under a fastener in the specified assembly to distribute load and maintain proper spacing. Replacing a worn or missing washer helps keep components tight, aligned, and operating smoothly.

• Distributes clamping force to prevent fastener pull-through and damage
• Maintains correct spacing/stack-up in the original assembly
• Helps reduce loosening, vibration, and premature wear at the joint
• Typical signs of trouble include rattling, looseness, or misalignment at the connection point

• Disconnect power (and turn off water supply if accessing a wet area)
• Use your model's parts diagram to locate and install the washer
• Replace one-for-one; reinstall any spacers or clips in the same stack sequence
• Tighten fasteners to manufacturer guidance—do not overtighten

This thrust ring is a small spacer that controls end-play on a shaft or gear, keeping parts aligned and reducing friction. Replacing a worn ring restores smoother, quieter operation and helps prevent premature wear in the assembly.

• Maintains axial spacing and limits end-play in rotating assemblies
• Reduces friction and metal-to-metal contact between components
• Helps stabilize shafts/gears to minimize noise and vibration
• Replace if you notice scraping/grinding sounds, wobble, or visible wear on the old ring

• Disconnect power before servicing
• Refer to your model's parts diagram to confirm orientation and stack order with any spacers/washers
• Clean the shaft and mating surfaces; replace any companion parts that show severe wear
• After reassembly, check for smooth rotation and proper end-play before returning to service

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

A replacement thrust bearing that supports the washer transmission shaft to reduce axial wear and help the gearbox rotate more smoothly. Use this bearing to address noisy transmission operation and reduce metal-on-metal wear when the original is worn. What it does:

• Supports axial load on the transmission/gearcase shaft to reduce friction and wear
• Helps prevent grinding, scraping, or other metal-on-metal noises from the gearbox
• Can reduce rough or noisy spin and improve agitation when a worn bearing is the cause
• Helps maintain proper alignment of transmission components for smoother operation

• Disconnect power and water supply and drain the washer before beginning any work.
• Replacement requires accessing the agitator/gearcase per the OEM service manual and may involve transmission/gearcase disassembly.
• Inspect nearby seals, fasteners and other bearings while servicing; replace damaged parts to avoid premature failure.

A replacement bearing that supports the washer drum and helps the tub spin smoothly with reduced friction and wear. Restores stable drum rotation to improve performance and reduce loud noises. What it does

• Supports the drum shaft so the tub spins evenly and stays aligned
• Reduces metal-on-metal contact that causes grinding or squealing noises
• Helps prevent excessive wobble or vibration during spin cycles
• Contributes to proper drum rotation that affects water extraction efficiency

• Disconnect power (and water for washers) before beginning any repair
• Access typically requires removing the cabinet or drum assembly; follow your model's service instructions
• Inspect surrounding seals and shafts for wear when replacing this bearing

This Support is a replacement mounting bracket that helps secure the appliance's internal assembly and restore proper alignment for smooth, quiet operation. Use it to replace worn or damaged supports that allow excessive movement. What it does

• Holds and stabilizes internal components to prevent wobbling or shifting during operation
• Helps reduce rattling, grinding, or knocking noises caused by loose supports
• Restores correct alignment to improve part engagement and function
• Prevents premature wear on adjacent parts caused by excess movement

• One Support mounting bracket

• Disconnect power (and gas if applicable) before beginning any repair
• Inspect surrounding fasteners and mounting surfaces; replace any damaged hardware
• Tighten to manufacturer torque specs where available; avoid over-tightening