Whirlpool Washer Dryer Combo Parts

The Knob is an OEM part for Whirlpool washers. This part allows users to select and control the various wash cycles and settings by turning the knob to the desired position. It fits securely onto the washer's control shaft, providing an intuitive a

Suspension spring that supports and balances the washer tub. Replace if broken, detached, or weakened to restore proper tub positioning and stability.

Dryer not heating or shuts off after a few minutes? A faulty thermostat often causes temperature regulation failure. Easy DIY fix with a multimeter test.

Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.

This small hardware washer sits under a fastener in the specified assembly to distribute load and maintain proper spacing. Replacing a worn or missing washer helps keep components tight, aligned, and operating smoothly.

• Distributes clamping forc
  Do-It-Yourself Stories from Customers like You Dryer drum was beginning to stall occasionally   Dana J E. • San Marcos , CA • March 17, 2015

  After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap... Read more

Dryer won't start but has power and timer works? This belt switch kit stops the dryer when the belt breaks. Moderate DIY repair, 45-60 minutes.

This internal-bias thermostat regulates dryer drum temperature by cycling the heat on and off, helping maintain consistent drying performance and protect against overheating.

• Controls the cycling temperature of the heating circuit to prevent und
  This part fixes the following symptoms

  • Too hot

  See more...
  Do-It-Yourself Stories from Customers like You Thermal fuse blew   John P. • Palm Coast , FL • January 02, 2016

  Cleaned exhaust duct, but only from the dryer/laundry room side. Replaced thermal fuse. Unit worked for about two loads and thermal fuse blew again. This time I cleaned the exhaust vent on the roof of my 2-story house. It was found to be partially obstructed and I was able to remove a significant amount of lint from it. Also, I researched the problem and followed someone's advice to replace the cycling thermostat together with the thermal fuse if the thermal fuse blows. So far it has been... Read more

Fix a dryer that won't heat or shuts off after 10-15 minutes with this thermal cutoff fuse. Common DIY repair for temperature detection issues.

Dryer won't heat? A failed thermal limiter opens the heating circuit when temperatures exceed safe limits. Simple DIY fix restores heat in 15-30 minutes.

Side or bottom exhaust vent kit for dryers. Relocates dryer vent from rear to side or bottom position. Includes metal duct, hardware, and instructions.

Replaces the upper tub ring that mounts on top of the outer tub as a splash guard. Order a new ring if yours is cracked, broken, or no longer securely attached.

Dryer motor used in washer/dryer stack units.

Includes two bumpers and two locking clips. You will use one or the other depending on hole size.

This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to preven

Missing or cracked cap letting water into the agitator? This protective cover seals openings and fasteners, preventing leaks and debris buildup. Easy DIY fix.

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides p
  Do-It-Yourself Stories from Customers like You Timer wouldn't advance on my dryer   John L. • Oblong , IL • March 22, 2016

  I ordered a new timer and installed it with the help of the videos provided and this did not solve my problem so I chated with the pros @ Appliance Parts Pros and told them my problem and they told me the problem and recommended the part I needed and With the incredibly fast shipping I had the part the next day. I installed it and now my dryer timer works great.Thanks to APPs for their help and ease of ordering and fast shipping. I highly recommend AppliancePartPros and will definitely use... Read more