Whirlpool Washer Pump

This circulation pump recirculates water through the spray arms during the wash and rinse cycles. Replacing a failing pump restores proper wash pressure and helps resolve poor cleaning, no-spray conditions, and loud humming from the motor.

• Recirculates water from the sump through the spray arms to clean dishes
• Maintains correct water flow and pressure during wash/rinse
• Common symptoms: tub fills but no spray action, poor cleaning results, loud humming/rumbling or grinding from the pump area, cycle stalls or runs long
• Restores consistent wash performance when the original pump motor has failed

• Disconnect power and shut off the water supply before service
• Access is from the bottom/front; remove the toe-kick and lower panels as needed
• Expect some residual water—use towels or a shallow pan
• Ensure the pump O-ring seats correctly; secure clamps/connectors and run a leak check after reassembly

This drain pump assembly moves water out of the appliance during the drain portion of the cycle. Replacing a weak or failed pump restores proper draining and helps prevent standing water, odors, or repeated drain attempts.

• Actively pumps wastewater through the drain hose to household plumbing
• Engages during the drain step to clear the tub/sump between and after cycles
• Typical failure symptoms: won't drain or drains slowly; water left in the bottom; loud humming/grinding during drain; leaks around the pump area
• May fail due to worn motor, damaged impeller, or debris lodged inside the pump

• Disconnect power and turn off water supply; bail or wet-vac any standing water before starting
• Keep towels or a shallow pan ready; clamp or plug hoses to control residual water
• Transfer hose connections and any mounting hardware from the original pump; ensure seals and clamps are seated firmly
• After installation, run a short cycle to check for leaks

This water recirculation pump moves wash water through the washer's recirculation circuit to help saturate loads and improve cleaning. Replacing a failed pump restores proper water movement and wash performance.

• Circulates water from the tub/sump back through the recirculation line during wash
• Maintains flow through the dispenser or spray nozzle for better saturation
• Replaces a pump that is noisy, leaking, seized, or not moving water
• Symptoms include no recirculation spray, reduced cleaning results, or a humming motor without water movement

• Disconnect power and turn off water supply before servicing
• Access is typically from the lower front or rear service panel; place towels to catch residual water
• Transfer hoses, clamps, and the electrical connector from the old pump to the new one
• Ensure correct hose routing and secure connections; check for leaks during a quick test cycle

This replacement filter traps debris and contaminants within your appliance's system to help protect internal components and maintain proper performance. Swapping a clogged or damaged filter can restore flow/airflow, reduce odors and buildup, and support efficient operation. What it does:

• Captures grease, lint, dust, or food particles to prevent recirculation and protect internal parts
• Supports proper airflow or fluid flow for ventilation, circulation, or drainage
• Helps minimize odors and residue caused by a saturated filter
• Typical signs it's due: visible tears/warping, heavy buildup, restricted airflow/venting, lingering odors

• 1 filter

• Disconnect power before servicing and allow any hot surfaces to cool
• Note the filter's orientation and any tabs/clips; install the new filter the same way
• Clean the surrounding housing or channel before installation
• Do not operate the appliance without required filter(s); follow your model's maintenance schedule

This is the water pump that moves water through your appliance so cycles can run correctly. Replacing a failing pump restores proper water flow and helps prevent standing water, poor performance, and leaks. What it does:

• Circulates and/or removes water as the appliance operates
• Supports proper flow so wash/rinse/drain steps can complete
• Maintains a sealed path at the pump connections to help prevent leaks
• Typical symptoms of a failing pump: standing water, weak/no water movement, loud humming or grinding from the pump area, leaks, or related drain/circulation errors

• 1 water pump

• Disconnect power and shut off water supply before servicing
• Have towels/containment ready; some residual water is normal when hoses are removed
• Move wires and hoses one-for-one to the new pump; tighten clamps and check any O-rings/seals
• Run a short test cycle and inspect for leaks and proper water movement

2 Port. Whirlpool and Kenmore washers.

This water pump moves wastewater out of the appliance so cycles finish and the tub stays clear of standing water. It replaces a failed pump to restore normal draining and cycle completion. What it does

• Pumps out drain water so the appliance can complete wash or rinse cycles
• Stops leaks from a damaged pump housing or worn seals
• Common symptom: appliance won't drain or has standing water after a cycle
• Can reduce or stop unusual grinding or humming noises coming from the pump area

• Disconnect power and water supply before beginning any repair
• Inspect hoses and seals for damage and replace if necessary when changing the pump
• Install with correct mounting orientation and secure electrical connections per OEM instructions

The Water Pump Assembly is an OEM part for Whirlpool washing machines. This part drains water from the washer during the wash and spin cycles. The water pump assembly ensures that water is efficiently removed from the drum, preventing overflows and ensuring proper rinsing and spinning of clothes.

Causes of a bad water pump assembly can include debris or foreign objects clogging the pump, motor failure, or damage to the impeller or seals.  

Symptoms of a bad water pump assembly include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Leaks from the pump area
• Error codes related to draining issues

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.