White Outdoor Parts

This drive belt is made for use on lawn mowers produced by multiple manufacturers. This belt attached the motor to the blade. This causes the driveshaft to rotate the blade. Because these belts are made of rubber, normal wear tear causes deterioration over time.Deterioration can take the form of cracking, tearing, or stretching of the drive belt. This can cause a complete breakdown of the lawn mower or reduced performance. If the mower is acting sluggish, it may be time to check the belt and replace it if necessary.Before removing and replacing the belt, it is important to drain the fuel tank and remove the spark plugs to ensure safety. Always disengage the blades and wear gloves when replacing the drive belt. After removing the damaged belt, slide the new belt on and reinstall the spark plug before operating the mower.This drive belt is OEM sourced. It is an individual part designed for use with edgers made by Troy-Bilt, Yard-Man, Yard Machines, Cub Cadet, and MTD.

This screw is a genuine Midwest Engine replacement part for appliances operated by small engines, including lawn tractors, lawn mowers, snowblowers, leaf blowers, vacuums, and tillers. The purpose of a screw is to link materials together by piercing into the materials and then rotating it until the materials are firmly clasped together.It is likely that a screw will have to be replaced at some point in the lifespan of an appliance due to simply losing or misplacing the screw. If the materials that are generally supposed to be held together seem to be loosening or have come apart, it is likely that the screw has either fallen out or has undergone damage that has warped it. This kind of damage can be attributed to general overuse, to age, or simply to long-term exposure. If a screw is subject to any of this kind of damage, it is best to replace it immediately. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This screw is compatible with the following brands: MTD, Cub Cadet, Troy-Bilt, and Yard Machines. This part sold individually.

This part is a replacement push cap. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. If the current push cap is broken or has been misplaced, this part can be used as a replacement. It is intended for use with several lawnmower models.The push cap is attached to the wheel hub cap and fits over the end of the axle shaft. This helps to protect the end of the shaft and the attached bolt that holds the wheel into position. When working on or near an engine, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this push cap, the appropriate owner's manual and equipment diagrams should be referred to. This push cap is suitable for use on a variety of lawnmower models manufactured by MTD, Yard Machines, Craftsman, Yard Man, and Troy-Bilt. It is a genuine OEM part and thus is made of high-quality, durable materials. This part is sold individually.

This discharge chute is a genuine MTD part, sold individually. This discharge chute can be used as a replacement part for a snowblower. This discharge chute provides a channel for the passage of snow that has been cleared out of the way by the snowblower so that the snow does not pack up tightly or blow in the face of the operator. The discharge chute of a snowblower might have to be replaced if it is not properly collecting and discharging snow or if the snow is packed too tightly to discharge properly. This could occur if the discharge chute has undergone too much scraping, scratching, or collision with the hard surfaces upon which it might be dragging. If this is the case, the discharge chute should be removed and replaced with this genuine OEM replacement part. Remember to wear work gloves as a safety precaution while repairing or replacing parts within an outdoor appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This discharge chute is compatible with the following outdoor appliance brands: MTD and Craftsman.

This flange bearing is a genuine MTD part, sold individually. This flange bearing can be used as a replacement part in a snowblower. The purpose of a flange bearing in a snowblower is to serve as a fastening component within the structure of the appliance.The flange bearing in a snowblower might have to be completely replaced at some point if the flange bearing can no longer facilitate the rotation or linear movement of one or more components within a snowblower. This could occur if the flange bearing has suffered damage as a result of general wear and tear with long-term use or due to collision with a hard object. If this occurs, the flange bearing should be removed and replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This flange bearing is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Huskee, and Yard-Man.

This deck lift pivot cup is an authentic OEM replacement part sourced directly from the manufacturer for use on riding lawnmower decks. This pivot cup separates the hex lock nut and the lift arm so that the arm can move freely while being secured to the deck. If the pivot cup is damaged or broken, the lift arm would not be able to move, and the deck would not be adjustable up and down. Regular maintenance and inspection will reveal problems with parts like the pivot cup, which can then be repaired. If the deck is not moving freely, the pivot cup should be checked and replaced if necessary. Park the mower on a flat surface and take the spark plug out for safety. Remove the deck mower and remove the blades. Locate the lift arm and the hex nut. Remove the hex nut and set it aside. Remove the damaged pivot cup and then insert the new one. Replace the hex nut and tighten it. Reverse the process to reassemble the lawnmower. This deck lift pivot cup is a metal part that is sold as a single unit. It is designed for use on lawn mowers and lawn tractors manufactured by MTD, Murray, and Craftsman.