Parts for Ge PSG22MISCFBB: 07 - Fresh Food Shelves Parts

This in-line water filtration system reduces water contaminants and improves taste of drinking water and ice. Reduces the taste and odor of chlorine through high quality carbon block media without removing minerals beneficial to your health. The filter should be replaced every six months or 300 galleons for best performance. The Quick Connect feature makes filter replacement fast and easy. Flow rate: 0.5 gpm/1.9 lpm. 1/4" quick connect fittings on both ends.

Size: 10-32 GXTT FLP.595 S

The Temperature Sensor is an OEM replacement part for GE refrigerators, designed to accurately monitor and relay the temperature inside the refrigerator and freezer compartments to the electronic control board. By detecting the slightest changes in internal temperature, the sensor allows the control board to make real-time adjustments to the cooling system, activating the compressor and fans as needed to maintain optimal conditions for food preservation.

Over time, the temperature sensor can fail due to electrical issues, exposure to moisture, or general wear and tear. A malfunctioning sensor can lead to improper temperature regulation, affecting the efficiency of the refrigerator and the freshness of stored food.

Symptoms of a bad Temperature Sensor include:

• The refrigerator or freezer not maintaining the set temperature 
• The appliance running continuously or more frequently than normal
• Inaccurate temperature readings displayed  

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Vegetable Pan is an OEM part for GE refrigerators. This part serves as a dedicated storage solution for fruits and vegetables within the refrigerator, helping to maintain optimal humidity levels and ensuring that produce stays fresh longer.  

Over time, the vegetable pan can experience wear or damage from frequent use, accidental impacts, or overloading. This can lead to cracks, warps, or breaks in the pan, which might affect its ability to properly store produce or fit correctly within the refrigerator.

Symptoms of a bad Vegetable Pan include:

• Difficulty sliding the pan in or out
• Produce not staying as fresh for the intended duration
• Visible cracks or damage to the pan
• Water accumulation beneath the pan due to improper sealing

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This OEM Replacement Part is a clear, meat pan designed for GE refrigerators. The pan measures approximately 20 inches wide, 9 inches high, and 17 inches deep. It is a pan designed to be placed inside the refrigerator compartment for storing and holding raw meats, poultry, or other foods that may produce juices or drippings.

A damaged or worn meat pan can lead to leaks, spills, and potential cross-contamination within the refrigerator. Causes of a bad meat pan may include physical impact, improper cleaning methods, or simply wear and tear over time.

Symptoms of a faulty meat pan include:

• Visible cracks, dents, or warping on the pan surface
• Difficulty sliding the pan in or out of the refrigerator compartment
• Leaks or spills due to improper containment of juices
• Rust or corrosion on the pan material

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

Color: white. It measures about 16 inches wide by 2 inches high by 2 inches deep.

Color: white. Measures about 3-1/2 inches wide by 1 inch high.

The Pan Cover Front Gasket is an OEM part for GE refrigerators. This gasket provides a seal for the front edge of the refrigerator's crisper or pantry drawer pan cover, preventing cold air from escaping and ensuring that the contents remain at the optimal temperature for freshness.

Common causes of a bad gasket include regular wear and tear, exposure to food spills, or accidental damage from frequent opening and closing of the drawer.  

Symptoms of a bad pan cover front gasket include:

• The drawer not sealing properly, leading to temperature fluctuations
• Visible cracks, tears, or warping of the gasket
• Increased condensation or frost buildup in the drawer area
• Food items spoiling faster than usual

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Color: white. It measures about 15 inches wide by 1 inch deep.

The Storage Pan Humidity Adjuster is an OEM replacement part for GE refrigerators. This part is located on the crisper drawer, the humidity adjuster allows you to open or close the air vent to the drawer. The adjustable panel controls humidity levels to keep foods fresher longer based on individual storage needs.

Causes of a bad humidity adjuster can include regular wear and tear, accidental damage, or issues with the sliding mechanism that controls humidity levels. If the adjuster becomes faulty, it can affect the preservation of your fruits and vegetables.

Symptoms of a bad Storage Pan and Humidity Adjuster include:

• Inability to modify humidity within the pan storage area
• Condensation buildup and dripping into the door compartment
• Noticeable loss of seals allowing air exchange with the outside environment
• Warped or broken panel preventing control of vent positioning

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Slide Bearing is an OEM part for GE refrigerators. This small but crucial component is typically located on the rails of refrigerator drawers, allowing them to slide in and out smoothly without sticking or jamming. The slide bearing helps reduce friction between the drawer and the frame, protecting the refrigerator's structure from wear and tear while ensuring a quieter, more efficient operation. 

Symptoms of a failing slide bearing include:

• Drawers becoming difficult to open or close
• Squeaking noises during drawer movement
• Increased resistance or jerking when pulling out the refrigerator drawers

Causes of slide bearing deterioration typically involve accumulation of food particles or debris, general wear from frequent use, or inadequate lubrication leading to increased friction and eventual wear out.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Slide Assembly RH is an OEM replacement part for GE side-by-side refrigerators. As a replaceable sub-assembly, it restores smooth extension of plastic vegetable/multi-purpose slides on the right interior. The slide measures approximately 16 inches.

Symptoms of a bad slide assembly include: 

• Drawers failing to fully extend or retract inward  
• Difficulty using bins and storage sections 
• Noisy operation of problematic slides
• Stress concentration leading to cracks along slides

Causes stem from extended use gradually degrading nylon rollers and wear strips through inevitable friction. Exposure to excessive weights above slide limits may also bend or warp steel support rails quicker.

This genuine GE replacement part is also compatible with Hotpoint, RCA, and select Kenmore models.

A replacement rear pan cover gasket that seals the refrigerator/freezer pan cover to help contain drips and reduce airflow under the pan. Restores a proper seal to support normal cooling and defrost operation. What it does:

• Seals the rear pan cover to help prevent water leaks and direct meltwater into the drain system
• Helps maintain correct airflow under the pan to reduce frost buildup and improve defrost performance
• Reduces the chance of water collecting under the cabinet that can cause odors or damage
• Fits and aligns with the pan cover to retain insulation and components in place

• One (1) rear pan cover gasket

• Install on a clean, dry pan cover surface; remove old gasket and any adhesive residue before fitting
• Warm the gasket slightly if needed to ease installation and ensure proper seating along the entire edge
• Use basic hand tools; avoid sharp tools that can tear the gasket

The Pan Snack Lower is an OEM part for GE refrigerators. This component is designed to store snacks and other small items in the lower section of the refrigerator, offering a convenient and organized storage solution. The pan slides in and out smoothly, making it easy to access your snacks and keep them fresh.

Causes of a bad pan snack lower can include physical damage from overloading or mishandling, cracks or breaks from wear and tear over time, or issues with the sliding mechanism that prevent it from operating correctly. A damaged or malfunctioning pan can reduce storage efficiency and accessibility.

Symptoms of a bad pan snack lower include:

• Difficulty sliding the pan in and out
• Cracks or breaks in the pan material
• The pan not staying in place or falling out
• Reduced storage efficiency within the refrigerator

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Right hand side

Left hand side

This slide rail is an OEM replacement part for GE refrigerators. The slide rail measures 1.25 inches in height, 2 inches in width, and 16 inches in depth.  This durable and reliable slide rail ensures smooth and effortless drawer operation. 

Causes of failure involve repeated impact stresses absorbing the weight of the heavy door opening and closing potentially thousands of daily times over 10-20 years. 

Symptoms of a faulty slide assembly include:

• Difficulty fully opening or closing the oven door  
• Binding, jamming or misalignment of door movement
• Visible bending or warping of metal slide track components
• Loose fasteners connecting assembly to cabinetry 

This OEM replacement part is also compatible with Hotpoint and RCA electric ranges as well.

NOTE: For the right-hand side order WR72X240. For the slide bearing order WR1X2048.

The Slide Assembly RH is an OEM replacement part for GE side-by-side refrigerators. As a replaceable sub-assembly, it restores smooth extension of plastic vegetable/multi-purpose slides on the right interior. The slide measures approximately 16 inches.

Symptoms of a bad slide assembly include: 

• Drawers failing to fully extend or retract inward  
• Difficulty using bins and storage sections 
• Noisy operation of problematic slides
• Stress concentration leading to cracks along slides

Causes stem from extended use gradually degrading nylon rollers and wear strips through inevitable friction. Exposure to excessive weights above slide limits may also bend or warp steel support rails quicker.

This genuine GE replacement part is also compatible with Hotpoint, RCA, and select Kenmore models.

The Slide Assembly RH is an OEM part for GE refrigerators. This slide assembly is designed to support and guide the refrigerator's drawers, ensuring smooth opening and closing. The slide measures approximately 10 inches x 1 3/8 inch x 1 5/16 inch. This is the right-hand side. For the left-hand side order WR72X241. For the slide bearing order WR1X2048.

Over time, the slide assembly can become worn out or damaged. Causes of a bad slide assembly can include frequent use, physical damage from overloading the drawers, or wear and tear on the sliding mechanism.

Symptoms of a bad Slide Assembly RH include:

• Difficulty opening or closing the refrigerator drawers
• Drawers not sliding smoothly or getting stuck
• Unusual noises when moving the drawers

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Left Hand Slide Assembly is an OEM component for GE bottom-mount refrigerators. It sits on the left side and smoothly guides the refrigerator shelf inserts in and out. This slide measures Approx 10 inches x 1 3/8 inch x 1 5/16 inch.

Symptoms of a faulty slide assembly include:

• Shelves difficult to fully extend or retract
• Grinding or rubbing noises from the shelf area 
• Visible signs of wear to plastic rollers and tracks

Causes relate to typical wear and tear over time under regular use. Improper loading of shelves can also potentially damage slide machinery.

For the right hand side order WR72X242. For the slide bearing order WR1X2048.

This GE replacement restores smooth shelf functionality, compatible with Hotpoint, RCA, and select Kenmore models as well.

This is a 10-24 x 1.0 inch screw used to secure appliance panels and components. It replaces worn or missing fasteners to restore proper fit and reduce rattling or loose parts for safer, quieter operation. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable
• Stops vibrating or rattling caused by loose or missing screws
• Restores proper grounding/attachment where a threaded fastener is required
• Matches OEM thread size and length for a correct fit when replacing damaged screws

• Use the correct driver bit and turn carefully to avoid stripping the head or threads
• Do not overtighten; snug until secure to prevent damage to mating parts
• Replace like-for-like with the same thread size and length for proper fit
• Disconnect power and follow appliance safety guidelines before accessing internal components