Parts for Speed Queen STGNCASP115TW01: Access Panel / Front Panel / Seal Parts

This push button switch mounts in the appliance's control panel and sends an electrical signal to the control when pressed. Replace a worn or sticking switch to restore dependable button response and function activation. What it does:

• Panel-mounted switch that closes its contacts when pressed to signal the control
• Restores reliable front-panel input for starting or selecting a function
• Helps address no response or intermittent response when the button is pressed
• Replaces switches with loose action, sticking, or heat-discolored/burned terminals

• 1 push button switch

• Disconnect power before servicing to avoid electrical shock
• Access the console/control panel to reach the switch
• Note wire positions (take a photo) and transfer connectors one at a time; ensure firm, fully seated terminals
• Secure the switch in the panel (nut/clip as applicable), verify button action, then reassemble and test

This Outer Tub Gasket seals the outer tub assembly in your washer to keep wash water contained through every cycle. Replacing a flattened, cracked, or leaking gasket helps stop water on the floor and protects internal parts.

• Creates a watertight seal between outer tub components
• Helps prevent leaks during fill, wash, and spin
• Common symptoms: water under the washer; moisture at the tub seam; visible cracks or compression set on the gasket
• Restores proper sealing after service or disassembly

• Disconnect power and water supplies; move the washer for safe access
• Access the outer-tub seam per your model's service procedure; note gasket orientation
• Remove the old gasket and clean mating surfaces; install the new gasket evenly without twists or gaps
• Reassemble and run a brief test cycle to check for leaks

This front panel replaces a cracked, worn, or damaged control console face to restore the appliance's appearance and protect the control components. It provides a clean mounting surface for the console controls and switches. What it does:

• Covers and protects the control area from spills, dust, and physical damage
• Restores a finished, factory look when the original panel is dented, scratched, or broken
• Helps keep buttons and switches aligned and accessible for normal operation
• Commonly replaced when the panel is cracked, warped, or cosmetically damaged

• Disconnect power to the appliance before starting any work
• Remove the console trim and mounting screws to access and replace the front panel
• Handle panels carefully to avoid scratching or bending during installation
• Reconnect power and verify controls operate correctly after installation

This appliance screw replaces a missing or damaged fastener to secure panels and brackets. With a 10B-16 thread and 0.34-inch length, it restores a tight fit to help reduce vibration, rattles, and loosening.

• Fastens sheet-metal parts, brackets, and covers in the appliance cabinet
• Helps maintain alignment and support of components subject to vibration
• Direct replacement for stripped, rusted, or missing hardware
• Can help resolve symptoms like loose panels, rattling noises, or gaps

• Disconnect power; shut off gas/water as applicable before servicing
• Start threads by hand in the original hole or clip to avoid cross-threading
• Tighten snugly without overtightening to prevent stripping
• If the receiving clip/nut is damaged, repair or replace it for a secure hold

This access panel assembly covers the washer's service area to protect internal components and give technicians a safe, removable entry point for maintenance. It restores the cabinet's exterior and keeps wiring and parts enclosed. What it does:

• Replaces a missing, dented, or damaged access panel to secure internal components
• Provides a removable service opening for accessing controls, valves, and wiring
• Helps stop debris and lint from reaching internal parts
• Reduces noise and vibration caused by loose or damaged panels
• Restores the appliance's finished appearance and safety

• Disconnect power and water supply before starting any service
• Typical installation requires removal of a few screws; use basic hand tools
• Handle edges carefully; panels can have sharp metal edges

A replacement self-tapping pan-head screw sized 10 x 5/8 in for securing appliance panels, trim and small assemblies. Restores proper fastening where original screws are missing, stripped or corroded. What it does

• Cuts its own mating thread in sheet metal or plastic for secure fastening
• Commonly used to attach control panels, trim pieces and small brackets
• Helps stop rattles, loose panels and misaligned trim when original fasteners fail
• Corrosion-resistant finish resists rust in typical laundry appliance environments

• Use the correctly sized screwdriver or driver bit to avoid stripping the head
• Start in a pilot hole if material is brittle or if reinstalling into worn threads
• Do not over-torque; stop when the head seats flush to avoid cracking or stripping
• Disconnect power and follow appliance-specific safety procedures before working

This door catch assembly secures the door when closed so the machine can run. A worn or broken catch can keep the door from latching firmly, causing start issues or interruptions during a cycle.

• Engages with the door strike/latch to hold the door shut
• If worn or damaged, the door may not close or stay closed
• Can lead to the unit not starting or stopping mid-cycle when the door moves
• Helps restore proper door latching and safety interlock function

• Unplug the appliance before service
• Open the door and remove fasteners retaining the old catch
• Transfer orientation from the original part to the new catch
• Test door closure and operation before returning to service