Parts for Speed Queen STGNCASP115TW01: Front Bulkhead / Felt Seal / Cylinder Parts

This front bulkhead assembly forms the dryer's front drum support and air seal. Replacing a worn or damaged bulkhead restores smooth drum rotation, reduces noise, and helps maintain proper airflow for consistent drying performance.

• Supports and aligns the drum at the front to prevent rubbing and scraping
• Helps seal the lint/air path so heat stays in the drum and exhaust flows correctly
• Air leaks at the front bulkhead can contribute to long dry times or lint in the cabinet

• Disconnect power and gas supply and allow the dryer to cool before servicing
• Remove the front panel/door assembly; support the drum before detaching the old bulkhead
• Transfer any model-specific components from the original bulkhead and ensure seals/glides are correctly positioned
• After installation, rotate the drum by hand to verify clearances, then reassemble and test

A clear silicone adhesive/sealant used to bond and seal appliance trim and components, helping restore watertight and stable assemblies. Supplies a durable, flexible hold for small repairs where factory adhesive is specified. What it does:

• Bonds trim, panels, and small plastic or metal parts to prevent movement and leaks
• Seals gaps to reduce water intrusion around housings and door areas
• Provides a flexible, durable hold that resists vibration and temperature changes
• Useful for reattaching trim, tabs, and molded parts when original adhesive has failed

• One (1) clear 3 oz tube of DOW 737 adhesive

• Use in a well-ventilated area; wear gloves and eye protection to avoid skin/eye contact
• Surface must be clean, dry, and free of oils or old adhesive for best adhesion
• Apply as a thin, even bead; allow recommended cure time before reassembling or using appliance
• Follow any OEM repair instructions and local disposal guidance for adhesive containers

This rubber rear drum seal fits the dryer drum opening and helps keep the drum centered while reducing air leaks and preventing lint and fabric from getting between the drum and bulkhead for quieter, more efficient drying. What it does:

• Seals the gap between the dryer drum and bulkhead to maintain proper airflow.
• Cushions the drum edge to prevent metal-on-metal contact and reduce noise.
• Worn or torn seals can cause rubbing, squeaking, banging, excess vibration, or longer dry times.
• Visible gaps, shredded rubber, or lint buildup at the drum edge are common signs the seal needs replacement.

• Disconnect electrical power (and shut off gas supply for gas dryers) before starting any repair.
• Replacement commonly requires partial or full drum removal; inspect the drum and bulkhead for additional wear while accessible.
• Wear gloves and eye protection; watch for sharp edges and pinch points during reassembly.

This seal kit restores a proper water-tight barrier in the washer's drive area to prevent leaks and protect bearings and motor components on 1992-and-newer units.

• Seals the drive shaft/tub interface to stop water migration
• Helps prevent bearing and motor damage from moisture
• Common leak symptoms: water under the washer, rust streaks at center post, noisy spin from moisture intrusion
• May also address oil/water contamination around the transmission area

• Disconnect power and water; move the washer to a stable, level work area
• Removal of agitator, inner tub, and drive components is typically required
• Inspect shaft and mating surfaces; clean and lightly lubricate as specified by service literature
• Use proper drivers/press tools; do not hammer seals into place

This white baffle cylinder is the replaceable tub/agitator baffle that helps move and separate laundry during the wash cycle for proper cleaning action. It restores agitation and water flow when the original baffle is worn or damaged. What it does:

• Channels water and works with the agitator/tub to help move clothes for improved washing action
• Helps reduce tangling and keeps items circulating through the wash zone
• Replaces cracked, broken, or excessively worn baffles that cause poor agitation or noisy operation
• Matches the original white finish for a factory appearance

• Disconnect power and water supply before beginning any repair
• Basic tools typically required; may need to remove agitator or access cap—refer to your model's service manual
• Inspect mating surfaces and fasteners; replace any worn hardware and ensure proper seating to avoid agitation issues

This is the rotating dryer cylinder assembly. Replacing a dented, rusted, or out-of-round cylinder restores smooth tumbling and helps prevent snags, noise, and uneven drying performance.

• Holds and tumbles laundry while working with the belt/drive system
• Internal white baffles lift and separate clothes for better airflow
• Smooth interior helps protect fabrics from catching or tearing
• Typical signs it's needed: loose or broken baffles, interior rust, dents, scraping/thumping once per revolution, or recurring fabric snags

• Disconnect power; for gas dryers, also shut off the gas supply
• Wear cut-resistant gloves—metal edges can be sharp
• Access typically requires removing the top/front panels and releasing belt tension; note belt routing
• Set drum, route belt correctly, spin by hand to confirm clearance, then reassemble and test

This Rulon 488 cylinder glide supports the front edge of the dryer drum at the bulkhead. Replacing a worn glide restores smooth, quiet rotation and helps eliminate scraping or squealing from the front of the drum.

• Provides a durable, low-friction surface between the drum rim and front bulkhead
• Supports the drum to minimize drag and wear for quieter operation
• Worn glide may cause scraping/squealing noises or a dragging drum
• Visible flat spots, grooves, or excessive wear on the glide indicate replacement

• Disconnect power and shut off gas supply before servicing
• Access the front bulkhead and support the drum to relieve load on the glide
• Remove the worn glide and clean the mounting area; install the new glide in the same position/orientation per factory fasteners
• Rotate the drum by hand to inspect felt seals and any additional glides and replace if worn

This genuine bracket secures a component inside your appliance cabinet, keeping it aligned and stable so the machine runs smoothly. Replace a bent, cracked, or stripped bracket to restore proper fit and prevent vibration, rubbing, and rattling.

• Provides a rigid mounting point for the specified assembly in your model
• Maintains correct position and spacing between parts
• Helps prevent vibration, rattling, and rubbing noises
• Replace if bent, cracked, or the mounting holes are stripped
• Common symptoms include loose/misaligned parts, unusual noises, or components not staying secured

• Unplug the appliance; shut off gas or water supply if applicable
• Support the attached component while removing fasteners
• Note orientation (take a photo) and transfer any clips/spacers from the original bracket if present
• Tighten fasteners evenly and verify alignment/clearances before use

This appliance screw replaces a missing or damaged fastener to secure panels and brackets. With a 10B-16 thread and 0.34-inch length, it restores a tight fit to help reduce vibration, rattles, and loosening.

• Fastens sheet-metal parts, brackets, and covers in the appliance cabinet
• Helps maintain alignment and support of components subject to vibration
• Direct replacement for stripped, rusted, or missing hardware
• Can help resolve symptoms like loose panels, rattling noises, or gaps

• Disconnect power; shut off gas/water as applicable before servicing
• Start threads by hand in the original hole or clip to avoid cross-threading
• Tighten snugly without overtightening to prevent stripping
• If the receiving clip/nut is damaged, repair or replace it for a secure hold

This felt pad cushions and isolates contact points inside the machine to reduce metal-to-metal contact, noise, and wear. Replace a worn or missing pad to help restore smoother, quieter operation and protect mating surfaces. What it does:

• Provides a soft, low-friction barrier between contacting parts
• Helps prevent squeaking, scraping, or rattling during operation
• Reduces wear at the specified contact point to protect components
• Visible thinning, glazing, or a missing pad can lead to noise and accelerated wear

• 1 felt pad

• Disconnect power (and gas/water, if applicable) before servicing
• Remove the old pad and clean the surface; align the new pad with the original footprint
• If adhesive-backed, apply to a clean, dry surface; reassemble and test for proper operation

The Glide Kit is an OEM replacement part for Speed Queen dryers. Designed for models manufactured in 1992 and later, this kit ensures the drum rotates smoothly during operation. It includes glide components that reduce friction between the drum and the dryer frame, allowing efficient and quiet performance.

Symptoms of a bad Glide Kit include:

• Squeaking or grinding noises during dryer operation
• Visible wear or damage to the glides upon inspection
• The drum becoming difficult to turn or feeling misaligned

Causes of a failing Glide Kit can include natural wear and tear over extended use, overloading the dryer, or improper alignment of the drum, which increases stress on the glides.

This OEM Speed Queen part is also compatible with Alliance laundry equipment.