Parts for Speed Queen STGNCASP115TW01: Front Panel / Door Assy / Door Seal Parts

The Outer Door Bezel Kit is an OEM replacement part for Speed Queen washing machines. As an exterior component, the door bezel surrounds and protects the outer edges of the washer door opening. 

Causes of a damaged bezel can include impact from repeated opening and closing of the door or general wear over extended use. Cracks or other deformations reduce its protective function.

Symptoms of a bad door bezel include: 

• Exposed edges of the door opening that could pinch or scratch skin 
• Loose or sagging pieces that impact the overall appearance
• Reduced structural integrity where the door seals close tightly

Replacing the bezel kit with this OEM Speed Queen part restores proper protection of the doorway. It maintains the washer's overall performance, comfort of use, and aesthetic appeal. This replacement is also compatible with residential washer models by Alliance Laundry Systems and some Dexter models.

This is a stainless-steel #8 x 1/2" Torx screw used to secure panels and components on Speed Queen appliances. Stainless construction resists corrosion for reliable fastened connections in laundry equipment. What it does

• Secures console, trim, panels, and internal brackets where a #8 x 1/2" Torx fastener is specified.
• Replaces missing or damaged screws that can cause loose panels, rattling, or misaligned components.
• Stainless-steel construction helps prevent rust in wet or humid laundry environments.
• Small, common fastener for service and reassembly after repairs.

• One stainless-steel #8 x 1/2" Torx screw.

• Use the correct Torx driver size to avoid stripping the screw head.
• Tighten finger-tight then snug; avoid over-torquing which can strip threads or crack plastic.
• Disconnect power (and water if applicable) before working on appliance internals to reduce shock or injury risk.

A replacement inner door bezel kit that restores the door trim and appearance of the washer or dryer. Replaces cracked, faded, or loose inner door trim so the appliance door looks and fits properly. What it does

• Replaces damaged or worn inner door trim to restore door appearance.
• Helps keep the door assembly aligned and prevents gaps around the door opening.
• Eliminates rattling or loose trim caused by cracked or broken bezel parts.
• Matches original gray finish for a consistent look with the rest of the cabinet.

• Disconnect power (and water, if applicable) before starting any repair.
• Basic hand tools (screwdriver) are usually required; keep removed hardware for reuse if undamaged.
• Handle door components and any glass with care to avoid breakage or injury.

The Inner Door Bezel is an OEM part for Speedqueen commercial-grade washing machines. This bezel frames the inside of the washer door opening, protecting internal components from damage. 

Causes of a bad Inner Door Bezel can include wear and tear from repeated use, exposure to harsh chemicals or cleaning solutions, or accidental impact damage. 

Symptoms of a bad Inner Door Bezel include:

• Cracks or breaks in the protective plastic material
• Loose or missing mounting screws  
• Scratches, discoloration, or other cosmetic damage
• The ability for liquid or debris to enter the washer opening

This commercial-grade Speedqueen part restores both function and appearance. It is specifically engineered to withstand high-traffic commercial laundering needs.

The Inner Door Bezel is an OEM replacement part for Speed Queen washing machines. It is a white plastic panel that mounts to the inside of the washer door providing structure and rigidity. The bezel acts as a backbone for attaching other door components like the door gasket, switches, insulation, and more.

Symptoms of a bad inner door bezel include:

• loose door components
• missing or damaged mounting tabs
• cracks along seams or corners
• uneven gaps around the door opening.

Causes of failure can be wear and tear from opening and closing the door thousands of times, exposure to cleaning chemicals or solvents over time, or physical damage from accidents.

This hex head machine screw fastens appliance panels and components, restoring secure assembly and stopping movement or vibration. It's a simple replacement when original screws are lost or worn. What it does:

• Secures panels, brackets, and internal components to prevent rattling or misalignment
• Replaces missing or damaged screw heads that keep parts firmly attached
• Restores proper fit where stripped or corroded fasteners allow play
• Helps maintain safe operation by keeping covers and guards in place

• Disconnect power and water before working on the appliance
• Use the matching hex driver or socket to avoid rounding the head
• Replace like-for-like; tighten until snug but avoid over-torquing
• If threads are damaged, inspect mating part and replace as needed

A durable door hinge that secures the appliance door to the cabinet and provides a smooth pivot for opening and closing. Replacing a worn hinge restores alignment to reduce sagging, rubbing, and poor latching. What it does:

• Provides a secure pivot point so the door opens and closes smoothly.
• Restores correct door alignment to prevent sagging, scraping, or uneven gaps.
• Helps the door latch and seal properly for safe, reliable operation.
• Reduces noise and binding caused by worn or bent hinge hardware.

• Disconnect power (and water supply for washers) before starting any repair.
• Support or remove the door to prevent dropping; use appropriate hand tools.
• Tighten mounting fasteners to firm engagement, then check door swing and latch operation.

A replacement self-tapping pan-head screw sized 10 x 5/8 in for securing appliance panels, trim and small assemblies. Restores proper fastening where original screws are missing, stripped or corroded. What it does

• Cuts its own mating thread in sheet metal or plastic for secure fastening
• Commonly used to attach control panels, trim pieces and small brackets
• Helps stop rattles, loose panels and misaligned trim when original fasteners fail
• Corrosion-resistant finish resists rust in typical laundry appliance environments

• Use the correctly sized screwdriver or driver bit to avoid stripping the head
• Start in a pilot hole if material is brittle or if reinstalling into worn threads
• Do not over-torque; stop when the head seats flush to avoid cracking or stripping
• Disconnect power and follow appliance-specific safety procedures before working

This large hose clamp secures flexible washing machine hoses and sealed door boots to prevent leaks and keep connections tight. Durable metal construction helps maintain a reliable seal at hose fittings. What it does:

• Clamps flexible hoses or bellows to fittings, sealing water or drain connections
• Keeps door boot or drain hose from slipping off and causing leaks
• Stops dripping or puddles caused by loose or missing clamps
• Works where a wider-band, heavy-duty clamp is required for a secure fit

• Disconnect power and turn off the water supply before servicing the appliance
• Loosen and remove the old clamp with a screwdriver or nut driver; position the new clamp and tighten securely
• Replace corroded or damaged clamps rather than reusing to ensure a proper seal

This door seal assembly creates a tight, durable seal around the appliance door to help keep heat and air inside the cabinet for efficient operation and consistent drying. It replaces a worn or damaged seal to restore proper door closure. What it does:

• Seals the gap between the door and cabinet to reduce air and heat loss
• Helps maintain consistent drying performance and cycle efficiency
• Prevents lint, moisture, and debris from escaping the drum area
• Reduces door-edge rubbing that can cause fabric wear or damage

• Disconnect power to the appliance before beginning any work.
• Inspect the door opening and gasket mating surface; clean away lint or residue before installing.
• Ensure correct seal orientation and full seating around the door perimeter; use existing clips/screws if applicable.
• After installation, run a short test cycle to verify the door closes properly and there are no leaks.

This black door boot seal forms a watertight barrier between the door and front tub on a front-load washer, keeping wash water contained. Replace a worn or torn seal to stop leaks and restore reliable operation. What it does

• Seals the gap between the door and front tub to prevent water leaks
• Helps direct water back into the drum during operation
• Maintains proper containment when filling, washing, and spinning
• Common failure signs: water leaking from the door/front, visible tears or cracks, or the gasket pulling loose

• Includes: 1 black door boot seal

• Disconnect power and turn off water supply before servicing
• Open the door and carefully release the inner and outer retaining clamps/springs
• Note the seal's orientation (alignment marks/drain ports) and install the new seal the same way
• Ensure both inner and outer lips are fully seated; reinstall clamps and run a short test cycle to check for leaks

This hex washer-head screw secures panels and components in commercial washers and dryers, providing a low-profile, vibration-resistant fastener that helps keep assemblies tight and aligned during operation. What it does:

• Fastens sheet metal and plastic parts where a wide bearing surface is needed
• Hex washer head spreads load to reduce pull-through on soft materials
• Self-tapping thread cuts into mating material for a secure fit without a nut
• Commonly used where vibration and repeated motion can loosen standard screws

• Use the correct size driver or socket to avoid stripping the head
• Start the screw straight and apply steady pressure while driving to ensure proper thread engagement
• Tighten until snug — avoid over-torquing which can strip threads or crack panels
• Disconnect power and follow all safety precautions before servicing appliance

This front panel replaces a damaged or worn control-console trim to restore the washer/dryer's appearance and protect the controls. It gives the machine a finished look and keeps buttons and switches secure from debris. What it does:

• Covers and protects the control area from impact, dirt, and moisture
• Restores proper mounting and alignment for control knobs and switches
• Resolves symptoms like cracked, bent, or missing front trim and loose controls
• Improves the appliance's appearance when the original panel is scratched or broken

• Disconnect power and water before beginning any work
• Remove control knobs and mounting screws to detach the old panel; retain hardware
• Align the panel tabs and screw holes, then secure with factory screws without over-tightening
• If trim clips are broken, replace them to ensure a secure fit.

This complete white door assembly replaces a damaged or worn dryer door to restore a proper seal and smooth opening. Designed for machines with a right-side hinge, it provides a ready-to-install replacement to get the door working correctly. What it does:

• Replaces the dryer door and right-side hinge to restore proper door swing and closure
• Helps reestablish a secure front seal for efficient drying and consistent tumbling
• Addresses common symptoms like a loose, sagging, or non-closing door
• Prevents further wear to the cabinet edge and latch by restoring correct alignment

• Disconnect power before beginning any repair and work with the dryer empty and cool
• Some models may require removal of the front panel for access; keep hardware organized
• Handle glass and painted surfaces carefully to avoid scratches; two people may be helpful for alignment
• Verify hinge orientation and latch engagement before final tightening