Admiral Auger, Helix, Crusher

• Ice maker dispenses too little ice
• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

My first hour: I investigated first by pulling out refridgerator to see if the water line hose was kinked. I started under the kitchen sink where it begins, coming from faucet water supply. Then I followed it to the back of the fridge to see if anything looked odd. Next I went to the ice maker itself. I investigated the ice maker by removing the freezer food sliding tray and hanging tray, and then unscrewing the door off the slides. When I looked inside at the ice maker, I saw the tube where... Read more

We bought a new ice guard and installed it. It is working really good now. Read more

Replaced the ice level arm Read more

I replaced the auger motor. You have to remove complete ice maker. Everything is just like help video to do except yoke dispenser. I watched video several times. Yoke will not just tap loose, after 30 minutes of tapping, I was using screwdriver to brace. I used a Dremel tool to cut part of shaft, came off easy then. After that, the repair went great. I have ice, I noticed motor I received was stronger. Parts came on time stated and worked great. I will order again on other repairs. Read more

All the corners of the Ice Bucket were cracked and was causing the screw inside the bucket to jam. Read more

Replaced icemaker and shutoff arm. Easy project. Read more

• Ice maker dispenses too much ice
• Leaking
• Ice maker not making ice

Watched online video and worked along - it was easy and quick - I was amazed! Read more

• Ice maker won't dispense ice

Removed old cap replace with new 5 min. works like new received new part in 2 days Read more

• Ice maker not making ice
• Ice maker won't dispense ice

Replaced both parts Read more

We found the right ice cub bin/pan, ordered it, and it arrived quickly. Fit perfectly, and it is now catching our ice. Read more

The removal of the ice bin and auger motor was easy but removing the auger from the shaft was another story. The auger was frozen to the shaft even after it sat out overnight. I carefully applied heat with a propane torch, directly on joint of the auger and the tip of the shaft, followed by a few drops of cold water. Once the shaft and auger cooled the auger separated easily. Putting the components back together was simple taking about ten more minutes. Read more

• Ice maker won't dispense ice
• Ice maker not making ice

Removed the broken ice enclosure tray, disconnecting and removing the motor and cube/crushed ice selector mechanism. Mounted the motor and selector mechanism to the rear of the new ice tray enclosure and installed the enclosure to the freezer compartment walls. Read more

Ordered new enclosure. Place ice maker into 'off' position. Remove ice tray assembly by pulling forward. Unscrew left hand side screw under old enclosure. Pulled broken part forward and up slightly. Unhooked wire harness from back of freezer. You can reach from underneath pulled out part. Or from top if you tilt rear of part down. Pull assembly out. Remove solenoid and motor. 4 screws each. Motor just needed plastic scarps removed. Remove auger drive fork (left hand thread = turn to... Read more

Replaced both parts Read more

Checked out the video on your site on how to disassemble the ice maker. Was really easy when you know the correct sequence. Only 3 screws and it's out of the freezer. Disassembled the ice maker on my kitchen counter and replaced the ice stripper. Reassembled and installed back in my freezer. It is as good as new Read more

Upon receipt of part (in 2 days), removed right panel (snapped on). Removed ice tray. Removed one screw holding broken tray. Then removed plug from motor/solenoid. Next, moved motor/solenoid from old cracked tray to new one. All holes aligned exactly. Replaced shelf/motor in freezer, and reconnected cable from motor to freezer wall. Put one screw back in. Then replaced right-side snap-in panel. Finally, slid in ice-tray itself onto the new shelf. Tested okay. Read more