Admiral Spring Parts

When I removed the cabinet, all of the springs appeared in tact, I had already replaced the counter balance spring so I knew that was not the issue. None of the suspension springs or brackets were broken but they did look worn/rusty so I replaced all of the brackets (2 in front and 1 large in back), all of the suspension spring retainers, and all of the suspension springs and it fixed the issue! I plan to also replace the Self leveling leg spring which is an easy fix since it's on the back of... Read more

This was the second attempt at fixing this problem. The first repair and parts were generated by listing the problem and reviewing the potential corrections, listed on the web site. From making repairs on other clothes washers, I was confident that some of those potential causes could have been the cause. Unfortunately the counterbalance spring and suspension springs were not the cause as they were attached as intended and in good condition. I reached out for Appliance Parts Pros input... Read more

Replaced Snubber Ring installed spring kit. Watched installation video, found it very helpful to plan repair. The washer runs like new now. Read more

My wife and I along with Mat on the video replaced the upper and lower friction pads, along with the balance springs. The machine runs smooth as it did new. Thank you everyone at Appliance Parts Pro and Mat. You are a great company. P.S. my wife and I should had made our own video for you since we are both in our 60s I bet it would have been funny Thanks Again. JIm & Debbie from Texas. Read more

• Will not agitate
• Burning smell

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

Replaced with thrust bearing kit. Watched your video and it took about 10 minutes to fix. Thanks Read more

I replaced drum rollers, axle shafts and front bearing kit. Still had noise. Ordered Idler Arm, Belt Tension Pulley & Washers. I ordered parts at 3:30 pm on a Wednesday, received new parts at 11:30 am Thursday. The instructions & videos were very simple to follow and provided excellent tips. Back up and running with silence in an 1/2 hour. My 13 year old dryer is running like new again. Way cheaper than calling a repairman. Read more

Without knowing exactly what broke I ordered 2 springs and 2 door spring links. I knew the door springs were weak and a parts man told me many years ago to always replace BOTH springs or the one you didn't replace will soon break. It is a simple procedure, just remember how the springs/links are attached. make a simple drawing or take a picture should you need it. I watched two "how to" video's which made it look harder to do than it really is. Turn the circuit breaker off and turn the... Read more

Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more

• Ice maker won't dispense ice

We ordered the Ice Door Fountain Kit and ice door spring, which was delivered to our home within three or four days. I understood everything about how to change it except the placement of the spring. A video on your website showed exactly how to put the spring in place and helped me get the job done quickly. It solved our problem and we really appreciate your services. Read more

• Door won't close

It was a simple fix. I removed the six screws holding the side panel on the range. Removed the broken parks of the spring. I use a screwdriver to help stretch the new spring into place. I then replaced the side panel and screwed it on. About ten minutes work. Read more

This is an easy home-owner repair! 1. Get down on the floor with a flashlight and a 5/16 nut driver, and remove the two screws holding the lower panel. Those screws are located beneath the lower panel, so you'll have your head on the floor to see 'em! 2. Lift the lower panel up and out. 3. Using the nut driver, remove the two kick-plate screws and lay the kick-plate aside. 4. Discard the broken spring. 5, Look at the remaining spring to determine where the spring should hook. 6. Hook... Read more