Amana Dryer Parts

Replaced relay and capacitor attached to compressor Read more

Replaced Read more

I end up take the top and front lid of the dryer in order to gain access to the drum, belt, and motor. i put the belt on and closed it all back up again. Read more

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

Replace the drum drive belt and tension pulley assy. Read more

• Too hot
• Shuts off too soon

I posted the following on the Facebook page ; SOoooo my 10 year old clothes dryer stopped and like almost everyone else I just figured it's shot, burned up, gotta get a new one. Well, due to a few bumps in the road I cannot afford another problem. My 2 vehicles are not running and with one being in the shop for 3 weeks and not being able to afford a rental car anymore this dryer was another headache. It sat for weeks and laundry started piling up. While looking online for sales somehow I... Read more

I referenced the repair video. Very straightforward and easy. Only need 3 tools: 1/4 and 5/16 nut drivers and Philips head screwdriver. About 15 minute job. Surprising how much lint and dust build up inside the chassis, was able to clean that out too. Read more

Unplugged unit from power. Removed two sheet metal screws and lower front panel, removed two sheet metal screws and door panel (disconnected three door switch wires and two light wires - noted the connected position of each wire ); removed three self-tapping screws and black plastic hot air outlet to fan duct from lower end of front bulkhead; removed sheet metal screws and front bulkhead; removed two sheet metal screws from dryer top panel and raised top up and back on rear hinge brackets;... Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

The heating element had a break in the heater coils, so I replaced it with a new one from Appliance Parts Pros. I also replaced the thermal fusible link and thermostat switch because they were so cheap it just made sense to go ahead and do it while I was in there. I also cleaned every nook & cranny in the dryer, then cleaned out the vent piping- which was about 100% clogged. The video's of how to tear down a dryer were indispensable to this repair - along with APP's always having the right... Read more

• Too hot
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more

I purchased the lid latch assembly and the lid switch strike. Following the clear video instructions for each part, my handy teenage son was able to remove the lid latch assembly and replace it with the new part as well as the lid switch strike. The washer is back to working perfectly for under $100. Appliance Parts Pros carry the parts to repair and at a lower cost than other online retailers. I saved about $30 compared to the other online site and I saved a service call fee. I'm so glad I... Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

• Marks left on clothes

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

Bought the leveling feet and screwed them in the bottom and they work great. Read more

• Too hot

The heating element had a break in the heater coils, so I replaced it with a new one from Appliance Parts Pros. I also replaced the thermal fusible link and thermostat switch because they were so cheap it just made sense to go ahead and do it while I was in there. I also cleaned every nook & cranny in the dryer, then cleaned out the vent piping- which was about 100% clogged. The video's of how to tear down a dryer were indispensable to this repair - along with APP's always having the right... Read more