Amana Dryer Parts

• No heat or not enough heat
• Takes too long to dry

I had to pop the lid up from the front with a screw driver, and behind the element was a metal piece, a heat shield, that had two screws that had to be removed from the back. The little part with the blue round tag (part of the kit that came with the element) was easily removed with one screw. Likewise, the element had a single longer screw holding it in on the right, and on the left a little rod was sticking through a hole in the metal, and you can merely move it to the side and up the slot,... Read more

Remove and replace Read more

• Too hot

The heating element had a break in the heater coils, so I replaced it with a new one from Appliance Parts Pros. I also replaced the thermal fusible link and thermostat switch because they were so cheap it just made sense to go ahead and do it while I was in there. I also cleaned every nook & cranny in the dryer, then cleaned out the vent piping- which was about 100% clogged. The video's of how to tear down a dryer were indispensable to this repair - along with APP's always having the right... Read more

I called a repairman and he wanted $230 to put in a new timer so I went online to Appliance Parts Pros.com and found the part and watched video on how to replace timer. The timer cost $89 and I received it in 2 days. It took about 3 minutes to replace and my dryer works great! Read more

I replace the old timer with the new one I purchased from appliance parts pros.com I removed the nuts from back of top console of the dryer. Removed the electrical prongs from the old timer and then replace with new timer than plug dryer in wall and started the dryer on timed cycle and the heating elements kicked in and my wife was smiling from ear to ear. Read more

I removed the front panel of the dryer and the metal cover over the blower wheel. Removed the lock ring and clamp. Removed the old wheel and placed the new wheel on the shaft. I thoroughly cleaned all the lint around the area and inside the front cover. I resealed the metal cover over the blower and reinstalled the front cover. Dryer works great. Easy fix, I spent more time thoroughly cleaning all the lint. Read more

Put in new LED lighrt module you sent me Read more

• Door won't close

I chatted with a rep on Appliance Parts Pros and found out which parts I needed for my model of dryer. Ordered the 2 clips that held the door closed. They arrived the next day!! My dryer was very different than the video but we were able to figure out which screws to remove. The old clips popped out and the new ones popped in. Took about 30 minutes because of there being a top and bottom clip to remove and replace and line up the door parts to screw the screws back in. It works great!! I... Read more

First I watched videos about squeaking Kenmore dryers. Then I used that information to open the dryer, diagnosing the fact that the roller on the drum belt tension arm had broken and actually fallen off the arm. The dryer was filled with lint and dust/dirt, so I also saw that the seals on the dryer had deteriorated greatly. AppliancePartsPros website is outstanding, far better than its competitors. This made it easy to find the parts and videos that I needed. It took hours to pull everything... Read more

• Marks left on clothes

After replacing thermal fuse once and having it fail a second time, I had to dig a little deeper to uncover the problem. I checked for blockage in the vent but everything was clear. I did, however, find that the drum had some up and down play in it. After closer inspection, I could see that the front drum seal was actually worn to the point that I could see a gap between the seal and the drum. I figured that the gap in the seal was letting air in and not letting sufficient air flow through the... Read more

Replaced the timer - This should have been a VERY easy repair however, there is a clip (holding the timer to panel) on the bottom of timer than must be removed with a pair of pliers. There is absolutely NO room to access this clip so I had to take apart much of the dryer to gain access. What should have been a 15 minute repair turned into a frustrating hour. Read more

Replaced it with a new seal Read more

• Shakes and moves

REPLACING THE SUSPENSION PADS AND REPLACE THE BALNCE RING EVEN IF MY DIDN'T LEAK ANY FLUID OUT OF IT... IT SOLVE THE PROBLEM, IT WORKS BETTER NOW THAN IT EVER DID, THE ONLY THING I COULD COME WITH IS THE MANUFACTURE PUT THE WRONG BALANCE RING IN IT TO START WITH... MY IS A 400 KENMORE TOP LOADER, IT IS THE EASIES WASHER I HAVE EVER TAKEN A PART.. I WISH CARS WERE THAT EASY... IT TOOK ME OVER A MONTH FIGHTEN THIS PROBLEM UNTIL I FOUND IT ON YOUTUBE... WHAT BLESSING IT WAS... Read more

Replaced the heater, both thermostats and the belt, works perfectly now!! Read more

Went on YouTube and found out how to replace switch. Had it replaced in no time. Read more

Ordered the parts from ApplianceParts Pros.com and saved the $100 service call. The fix was easy, complete instructions enclosed. Read more