Amana Parts

The Lint Screen Door is an OEM part for Whirlpool dryers. It is located at the front of the dryer and provides easy access to the lint screen. It helps to trap lint and debris from the drying process, preventing it from entering the dryer vent and potentially causing clogs or fire hazards.

Causes of a faulty or damaged lint screen door can include regular wear and tear, physical damage, or improper handling. These factors can result in issues such as difficulty in opening or closing the door, a loose or insecure fit, or reduced effectiveness in capturing lint.

Symptoms of a bad lint screen door may include:

• Difficulty in opening or closing the door
• Loose or wobbly door fit
• Lint bypassing the lint screen and accumulating in the dryer vent

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Color: Gray. Measures about 16 inches wide by 7 inches high.

Color: metallic. Measures about 11 inches wide by 2-1/2 inches high.

A lint filter or lint trap prevents clogging of the dryer vent. When a garment is tumbling around in the dryer, the high heat combined with agitation can lead to fiber shedding. The lint filter captures the fibers and prevents them from blocking the dryer vent hose. If there is too much accumulation already, the excess fibers may not stay in the filter and could flow into the hose. Installing a brand-new lint filter can solve this problem. It can promote better energy consumption, faster drying, proper airflow, and reduced fire risk. Replacement is simple and straightforward and no tools are needed. Open the dryer and access the lint filter housing. Open the cover and slide the old filter out. Insert the replacement. This SpeedQueen 61376P Lint Filter is a genuine replacement part that will work with dryers made by Amana, Kenmore, SpeedQueen, and Caloric. It has a screen and a plastic frame. This OEM SpeedQueen lint filter is sold individually. A gas valve coil kit is available but sold separately.

This small strainer sits inside the washer's water inlet valve and screens out sand, rust, and sediment from the supply lines. Replacing a clogged or missing screen restores normal fill flow and helps protect the valve.

• Filters debris from incoming hot and cold water before it reaches the valve and tub
• Helps maintain consistent water flow during the fill cycle
• A clogged or damaged screen can cause slow fill, very long fill times, or no fill
• Common causes for replacement include mineral buildup or rust/sediment from supply lines

• Unplug the washer and turn off both water supplies
• Place a towel or shallow pan, relieve hose pressure, and disconnect the fill hoses from the inlet valve
• Carefully pull out the old screen (needle-nose pliers work well); press the new screen fully and evenly into the valve port
• Reconnect hoses, restore water and power, and check for leaks
• Tip: Many washers have separate hot and cold inlets—inspect both screens and replace as needed

Color: metallic. Measures about 10 inches wide by 5 inches deep. Be sure to measure old filter before ordering. If your filter measures approx 11 1/4" x 6 1/8" use R0710163.

This fine mesh plastic screen filters debris from the water path to protect downstream components and help maintain proper wash performance.

• Traps fine particles to prevent clogs in the circulation/inlet path
• Helps reduce spray pressure loss and poor cleaning results
• Can address issues like gritty residue, reduced water flow, or noisy pump operation
• Wear, mineral buildup, or tearing can require replacement

• Disconnect power and shut off water before service
• Note orientation and seating of the original screen; install the replacement fully and evenly
• Inspect surrounding seals and mating parts; clean any sediment before reassembly
• Restore power/water and check for leaks and proper operation

This factory replacement filter helps protect your appliance's internal systems by capturing debris and contaminants, maintaining proper flow and performance. Replacing a damaged or clogged filter can help restore efficiency and prevent avoidable wear.

• Screens particles from the air or water stream to safeguard internal components
• Helps reduce buildup that can lead to odors, residue, or restricted flow/airflow
• Replace if torn, warped, broken, or persistently clogged
• Common symptoms include reduced performance, unusual noises, residue buildup, or poor circulation

• Disconnect power (and shut off water supply if applicable) before servicing
• Access and removal method varies by model; note orientation and locking tabs or latches
• Do not force the filter; align and seat fully to ensure a proper seal
• Never operate the appliance without all required filters in place; refer to your model's user guide for specifics

This Whirlpool Water Filter Housing is an OEM part for specific Whirlpool refrigerator models. It plays a role in accommodating the water filter, ensuring clean and safe drinking water is dispensed from your fridge. 

A faulty housing may lead to water leaks, improper filter fitting, or reduced effectiveness in water filtration, affecting the quality of the water dispensed.

Symptoms of a bad water filter housing include:

• Leaking water near the filter area.
• Difficulty in installing or removing the water filter.
• Unusual noise or vibration when the water dispenser is used.
• The water filter does not lock in place securely.
• Noticeable decrease in water flow from the dispenser.

This genuine Whirlpool OEM replacement part is compatible with Maytag, Jenn-Air, and Kenmore models.
 

this is not a filter. The water filter bypass attaches in the water filter head and allows the water to flow to the dispenser and ice maker when the filter has been removed. Approximate dimensions: 4.37" x 2.87" x 2.5"

Color: gray. Measures about 13 inches wide by 11-1/2 inches high.