Amana Range Parts

LP conversion kit for gas ranges. Includes orifices and fittings needed to convert your range from natural gas to liquid propane fuel source.

Color: Black. Instruction sheet included.

Fix burners that won't light with this cooktop igniter switch wire assembly. Restores reliable spark ignition when switches fail. Moderate DIY repair.

LP gas conversion orifice kit for range top burners and oven. Includes orifices needed to convert from natural gas to propane. Essential hardware.

Burner cap covers and protects the burner head on gas ranges and cooktops. Replace if cracked, chipped, discolored, or missing to restore appearance.

Outer glass frame panel for wall oven doors. Replaces cracked, chipped, or broken door glass to restore appearance and visibility while maintaining heat.

This square drip pan is used on gas ranges. Color: chrome. It measures about 8 inches wide by 8 inches deep.

This replacement screw secures appliance panels, brackets, or internal components to keep them tight and aligned. Replace a missing, stripped, or damaged fastener to restore a solid, rattle-free fit and reliable operation.

• Fastens parts to the cabinet or frame to prevent movement
• Replaces missing, stripped, or corroded hardware that can cause looseness, vibration, or noise
• Helps correct gaps or misalignment after service
• Maintains proper support for covers, trims, or brackets

• Disconnect power; shut off gas/water if applicable before servicing
• Match screw length and location to the original position
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace damaged clips/inserts before installing the new screw

Burner won't turn down from high or stays on? This infinite switch regulates heat to surface elements. Common DIY fix for overheating burners.

This 250V, 1A fuse protects your washer's control circuit from overcurrent. Replacing it can restore control power once the root cause is corrected.

• Opens to protect electronics when current exceeds its 1A rating
• Check this part if the washer has no power, the control panel is dead, or it won't start
• A blown fuse will test open for continuity
• Repeated failure points to an underlying short or component fault that must be fixed

• Disconnect power before servicing
• Access the fuse at the control board or fuse holder
• Replace only with the same rating: 1A, 250V
• Inspect wiring/components and correct any short before restoring power

Color: metallic. Measures about 10 inches wide by 5 inches deep. Be sure to measure old filter before ordering. If your filter measures approx 11 1/4" x 6 1/8" use R0710163.

White thermostat control knob for gas and electric ranges. Replaces worn, cracked, or broken temperature selector knobs. Includes metal insert for secure fit.

This rear latch assembly secures the dryer door so the appliance can latch and run properly. It replaces a worn or broken rear latch to restore reliable door closure and help the dryer start and stay closed during cycles. What it does:

• Secures the dryer door to engage the door switch so the dryer will start
• Keeps the door closed during operation to prevent interruptions mid-cycle
• Replaces a broken, bent, or worn latch that prevents the door from latching
• Commonly used when the dryer won't start, stops unexpectedly, or the door won't stay closed

• Disconnect power (unplug or switch off breaker) before beginning any work
• Installation may require removing the dryer top or front panel; follow the model's service instructions
• Handle panels and metal edges carefully to avoid cuts
• After installation, verify the door latches securely and the dryer starts before reassembling all panels

Cast iron burner grate for gas ranges. Installs over cooktop burner. Replace if grate is cracked, broken, or has damaged feet. Black finish.

Restores a heat-resistant seal around your oven door. Replace when torn or damaged to maintain accurate temperatures and contain heat. Confirm fit by model.

This orifice spud meters gas to the burner for a consistent, correctly sized flame. Replace a clogged or damaged spud to restore proper burner output and reliable ignition on your gas cooktop or range.

• Controls and meters gas flow through a calibrated opening to the burner
• Helps ensure proper flame size and color when matched to the correct burner and fuel type
• Common symptoms of a failing or clogged spud: weak or uneven flame, yellow tipping, or delayed ignition
• Damaged threads or a stripped orifice can prevent correct sealing and fuel delivery

• Shut off gas supply and disconnect power; allow the appliance to cool
• Access the orifice holder/manifold for the affected burner; remove the old spud with an appropriate orifice wrench or nut driver
• Start the new spud by hand to avoid cross-threading; tighten snugly—do not overtighten brass threads
• Restore gas and check for leaks with an approved leak-detection solution; verify flame quality and adjust per the service manual