Amana Range Parts

Supports and guides your range oven door for smooth opening and closing. Replace if hinge is bent, broken, or worn causing door misalignment or drooping.

Color: Stainless

Holds and positions the burner orifice above the surface burner on gas ranges. Replace if cracked, broken, or damaged to restore proper burner alignment.

Controls gas flow to your range burner for proper flame size. Replace if orifice is worn, clogged, or damaged to restore accurate gas metering.

Replace a worn, cracked, or missing control knob on your gas range. Fits onto the control shaft to restore manual selection of burner settings.

Replacement screw for range and oven assemblies. Secures panels, brackets, and internal components. Order if original is stripped, missing, or damaged.

Controls gas flow to your range burner for proper flame size. Replace if cracked, clogged, or missing to restore precise gas metering and safe operation.

This spark ignition switch initiates the electrical spark that lights the gas burners on your range cooktop. It provides the timing and electrical signal needed for reliable burner ignition. Replace this switch if your burners won't light, have delayed ignition, or require multiple attempts to start.

Shoulder screw for securing range components. Installs underneath the unit. Replace if missing, stripped, or damaged to properly fasten parts together.

The Door Handle is an OEM component for Whirlpool dryers. It provides convenient access to load and unload clothes through the dryer door opening. 

Causes of a bad door handle can include normal wear and tear over extended use. Repeated clutching and releasing of the handle leads to fatigue of rubberized grip areas and loosening of mechanical connections. Accidental falls or impacts when transporting dry loads of clothes could also damage the handle structure or mounting.

Symptoms of a bad dryer door handle include:

• Increased play, wobble, or looseness when grasped  
• Detachment or separation from the door assembly
• Cracks, splitting, or broken areas compromising the grip surface
• Inability to smoothly open or close the dryer door

Compatible models also include Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore dryers.

Pilot burner assembly for right-side surface burners on standing-pilot gas ranges. Replace if clogged, damaged, or failing to maintain a stable flame.

This oven thermostat regulates your range's cooking temperature. It senses the oven cavity and switches the heat on and off to maintain your set point, helping restore accurate, consistent baking and roasting results.

• Regulates oven temperature by sensing heat and cycling the burner/element to hold the set point
• Symptoms of a failing thermostat include running too hot or too cool
• Food may bake unevenly, be undercooked/overcooked, or the oven may not reach the set temperature
• Preheat may take excessively long or temperature may swing widely
• Heat may not cycle off once the set temperature is reached

• Disconnect electrical power; for gas ranges also shut off the gas supply
• Allow the oven to cool completely before service and use proper PPE
• If your original uses a sensing bulb/capillary, route and secure it exactly as the original and avoid kinks or sharp bends
• After installation, verify temperature with an oven thermometer and perform user calibration only if your model supports it

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

White plastic oven door handle for electric and gas ranges. Replaces cracked, broken, or damaged handles. Installs on outer door panel with screws.

Burner orifice spud for gas ranges. Meters gas flow to control flame height. Replace if clogged, damaged, or when converting between natural gas and LP.

Pilot burner assembly with thermocouple for gas range ovens. Replace if pilot won't stay lit, flame is weak, or assembly is cracked or corroded.