Parts for Ge GTX22EASK0WW: Backsplash, Blower & Motor Assembly Parts

Replace your dryer's control knob when broken, cracked, or stripped. Mounts to the control panel for selecting cycles and settings on GE dryers.

This Backsplash Assembly is an OEM part for GE dryers. This assembly not only contributes to the structural integrity of the dryer but also houses important functional aspects, ensuring that the controls and connections are properly enclosed and protected. 

The need to replace the backsplash assembly can be due to damage, wear and tear, or issues with the control mechanisms housed within it. A malfunctioning backsplash assembly can affect both the operation and appearance of the dryer.

Symptoms of a faulty Backsplash Assembly include:

• Damage or wear compromising the structural integrity of the dryer.
• Issues with control panel connections or responsiveness.
• Misalignment affecting the fit and closure of the dryer's rear section.
• Visual imperfections that impact the overall appearance of the appliance.
• Difficulty in accessing or using the control features properly.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Rotary Knob is an OEM replacement part for GE or Hotpoint washing machines. It provides the interface for selecting wash cycles and adjusting settings like temperature and spin speed.

Causes of a bad rotary knob include cracking, peeling, or damage to labeling from repeated use over time. The internal mechanisms can also wear out, preventing proper rotation.

Symptoms of a bad rotary knob are:

• Difficulty turning or clicking into set positions
• Loose, wobbly, or disconnected feel during use
• Faded or missing labels make settings unclear

It is also compatible with RCA, Westinghouse, Tappan, and some Kenmore models.

Dryer won't start when you press the button, or stops when released? The push-to-start switch often fails. Easy 20-minute DIY repair with video.

Rear access panel for dryers. Covers the back of the dryer cabinet and provides access to internal components. Replace if cracked, damaged, or missing.

Secures dryer panels and internal components to the cabinet frame. Replace if screw is stripped, missing, or loose to prevent vibration and rattling.

Replace a cracked, worn, or missing washer in your dryer. This small hardware component ensures proper spacing and tension between parts during operation.

Fix a dryer that won't start or runs only on high heat with this rotary switch replacement. Controls temperature and cycle settings. DIY-friendly repair.

Dryer won't advance through cycles or stops mid-cycle? The timer controls cycle duration and progression. Moderate DIY repair with basic tools.

Factory screw that secures dryer panels, brackets, and internal components. Replace missing, stripped, or damaged screws to restore proper fit and alignment.

Fix intermittent power, faulty controls, or non-working elements with this dryer wire harness. Routes electrical power between components for safe operation.

The Blower Wheel is an OEM component specifically designed for GE dryers. It is responsible for circulating air during the drying cycle, directing airflow through lint and clothes to remove moisture. The plastic blades of the blower wheel push air through the dryer and out the vent when the motor is running. 

Symptoms of a bad blower wheel include:

• Slow or inefficient drying times even on low moisture loads    
• Strange noises from inside the dryer cabinet      
• Excessive vibrations felt through the dryer door or cabinet
• Bent or cracked blower wheel blades

Causes can include normal wear and tear over time, accidents that damage the blades, or failures in the secure mounting of the blower wheel.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

Secures the drive motor to its mounting bracket. Replace if cracked, broken, or missing to keep the motor and blower aligned and stable during operation.

Metal bracket that secures the dryer motor and blower assembly in place. Replace if your mounting bracket is cracked, broken, or causing loose components.

Transfers power from motor to drum in your dryer. Replace if squeaking, not spinning, or visibly worn. Confirm fit with your model number before ordering.

Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.

Idler pulley for dryer drum assembly. Maintains belt tension to enable smooth drum rotation. Replace if worn, cracked, or causing noise during operation.

Seals the blower-to-exhaust duct connection in your dryer. Replace if torn, brittle, or causing heat loss and longer dry times. Confirm fit by model.

Dryer taking too long or not drying? This blower housing directs airflow from motor to drum. Restores venting and drying performance. Moderate DIY.

Routes hot air from blower to external vent. Replace if cracked or leaking to restore airflow and prevent lint buildup. Confirm fit with model.

If your dryer runs but produces little or no heat, the thermostat may have failed. This safety sensor monitors drum temperature during cycles.

Replacement mounting screw for dryer panels and components. Needed when original screws are stripped, missing, or damaged during repair or maintenance.

This plate motor drives the microwave/oven turntable, keeping the glass tray rotating for even cooking and heating. Replaces a worn or failed motor to restore tray rotation and reduce uneven heating. What it does:

• Turns the glass turntable so food cooks evenly
• Stops rotation or hesitates when motor fails or wears out
• May make buzzing, grinding, or intermittent noises before failing
• Prevents the turntable from rotating if the motor no longer engages

• One replacement plate (turntable) motor

• Disconnect power before servicing to avoid shock; verify unit is fully powered off
• Remove the turntable glass and roller guide to access the motor underneath the oven/microwave floor
• Typical install requires removing interior fasteners and unplugging the motor connector; retain hardware for reassembly

Replace missing or stripped mounting screws in your washer dryer combo. This 12-pack secures panels, components, and internal parts during assembly or repair.

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

Fix a dryer that hums but won't start with this motor drive and pulley assembly. Powers the drum and maintains proper belt tension and alignment.

Replacement start button for dryer control panel. Installs on front console. Needed when original button is cracked, broken, or won't depress properly.

The MOTOR & BLOWER ASSEMBLY is an OEM part for GE dryers. It contains both the drive motor that tumbles the dryer drum as well as the blower motor that circulates air through the heating system. This dual-component assembly works together to simultaneously tumble clothes while pushing heated air into the dryer cylinder.

Causes of a bad motor and blower assembly can include failures of either the drive motor or blower motor. Wiring issues or damaged components internal to the assembly housing can also impact performance.  

Symptoms of a bad motor & blower assembly include:

• The dryer drum not spinning or tumbling clothes
• Inadequate or no airflow through the dryer 
• Dryer not heating or cycles taking excessively long
• Loud buzzing or grinding noises from internal motors

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Fix a dryer timer that won't advance or automatic cycles that stopped working. This timer resistor regulates cycle duration. Easy 15-minute repair.

The Interlock Switch is an OEM replacement part for GE electric and gas dryers. This safety component monitors the door closure, preventing operation if the door is not securely closed and latched. The switch measures 2 inches long and 1/2 inch wide.

Symptoms of a faulty interlock switch include:

• Dryer failing to start or running with the door open  
• Timer display not illuminated when start button is pressed  
• Inability to open the dryer door during operation
• Dryer suddenly stopping mid-cycle before fully drying clothes

Causes relate to the internal component contacting the door frame over 50,000 open/close cycles potentially exposing wiring to wear. Regular cleaning the external switch area prevents dust or lint buildup skewing performance. 

This genuine GE switch is compatible with Hotpoint and RCA dryers as well.

Note: Can be used as a dishwasher door switch on specific models. Check your model number for the most accurate results.