Bosch Parts

A 15 amp cartridge fuse that protects appliance electrical circuits from overcurrent, helping prevent damage to controls and components. Fits into inline fuse holders or boards where that specific fuse rating is required. What it does

• Interrupts circuit power when current exceeds 15 amps to protect wiring and electronics
• Commonly linked to symptoms like no power to controls, unresponsive display, or appliances that won't start
• Designed to be replaced when visibly blown or when continuity test fails
• Works as the exact rated safety fuse specified for compatible appliances

• One 15 amp cartridge fuse

• Disconnect all power to the appliance before accessing or replacing the fuse
• Replace with the identical fuse type and 15 amp rating only; do not substitute different ratings
• Handle carefully and mount fully seated in its holder or on the PCB as designed
• If the new fuse fails again immediately, stop — repeated failures indicate underlying electrical faults

This front drum motor mounting bushing supports the dryer drum shaft and helps the drum spin smoothly for quiet, even drying. It replaces a worn bearing surface to reduce noise and prevent drum misalignment. What it does:

• Provides a low-friction bearing surface for the drum shaft at the front motor mount
• Helps keep the drum properly aligned during rotation
• Reduces squealing, grinding, or rubbing noises caused by a worn front bushing
• Prevents excess wear on the drum shaft and adjacent components when functioning correctly

• One front drum motor mounting bushing

• Disconnect power before beginning any repair and follow all safety precautions
• Inspect the drum shaft, drum seal, and rear bushing for wear and replace as needed
• Use appropriate tools to remove the old bushing and press or seat the new bushing evenly
• Re-check installation and related components if alignment or noise persists after replacement

This stainless steel cooktop control knob replaces a worn or damaged selector on electric Bosch cooktops, restoring a solid grip and accurate temperature control. Designed to match factory fit and appearance for a clean, functional finish. What it does:

• Replaces a damaged, faded, or loose control knob so you can safely select burner settings
• Provides a clear tactile stop for reliable temperature selection
• Restores the original appearance of the cooktop surface
• Helps prevent accidental knob movement caused by worn parts

• Turn power to the appliance off at the breaker before servicing to avoid electrical hazard.
• Pull off the old knob straight away from the shaft; align the new knob with the shaft and press on until fully seated.
• If the knob does not fit, verify shaft type and part number before forcing.

The Pressure Regulator is an OEM replacement part for Bosch gas cooktops. It maintains consistent burner flame levels for precise meal preparation, maximizing fuel efficiency. Even pressure safeguards safety through controlled gas flow.

Causes of a bad pressure regulator can include deteriorating diaphragm seals or valve shafts due to repetitive operations over the appliance's lifespan. Mineral scales from sediment in gas lines threaten integrity.

Symptoms of a bad pressure regulator include:

• Flames lift or flare away from burner heads unpredictably   
• Burners cannot maintain set heat levels, constantly cycling 
• Difficulty achieving desired flame height or cooktop shuts off
• Potential safety hazards like uncontrolled gas leakage

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This terminal block is the appliance wiring connector that secures incoming power and links internal circuits, restoring a safe, reliable electrical connection. Replaces a damaged or burned block to help prevent intermittent power or arcing. What it does

• Provides a secure connection point for incoming power leads and internal wiring
• Restores continuity when a cracked, corroded, or burned terminal causes loss of power
• Helps stop arcing, sparking, or overheating at the power entry point
• Used where multiple wires must be joined and fastened to the appliance chassis

• One terminal block

• Disconnect all power before inspecting or replacing the terminal block
• Verify wire locations and take photos or label wires before removal for correct reassembly
• Tighten connections to manufacturer torque spec—do not over-tighten screws
• If you see extensive burn or damaged wiring, replace damaged wires.

Includes(1)Shipping Bolt,(1)washer,(1)sleeve

The Shipping Bolt is an OEM part for Bosch washing machines. This bolt is designed to secure the washer drum assembly during shipping to prevent excessive movement and potential damage.

Causes of a bad shipping bolt can include stripping, damage to the threads, or loss of the bolt entirely during shipment or installation.

Symptoms of a damaged or missing shipping bolt include:

• Excessive shaking or rattling noises from inside the washer drum
• The drum not rotating properly during wash cycles
• Reduced washing efficiency and improper washing performance

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This push-on retainer clip holds a 6mm shaft securely in place on compatible appliance components, restoring proper axial restraint and preventing parts from sliding off during operation. Simple, low-profile fastening for shaft retainment. What it does:

• Secures shafts and spindles with a 6mm outer diameter to prevent axial movement
• Keeps knobs, pulleys, or rotating components positioned correctly during use
• Commonly used where a quick, tool-free clip is required for retention
• Can resolve symptoms like loose or detached knobs, wobbling pulleys, or parts sliding along the shaft

• One push-on retainer clip sized for 6mm shaft mounting

• Push the clip onto the shaft groove until it snaps into place; ensure full engagement before operating
• Use snap-ring pliers or appropriate tools if removal is required to avoid damage
• Wear eye protection when installing or removing clips to guard against sudden release

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This heating element replaces the dishwasher tub heater to warm wash water and support drying performance. Restores proper water temperature so detergents and rinse agents work effectively during cycles. What it does:

• Heats wash and rinse water to help remove soils and dissolve detergent
• Supports the dry cycle by raising tub temperature for improved moisture removal
• Helps maintain correct cycle temperatures for sanitation and cleaning performance
• A failed element can cause no-heat conditions, poor drying, or extended cycle times

• Disconnect power to the appliance before starting any work to avoid electric shock
• Inspect and replace only the element shown in the service diagram; handle with care to avoid damage
• Verify electrical connections and test the element for continuity with a multimeter before and after installation

This replacement lid with insert fits compatible Bosch countertop blenders to keep ingredients contained while blending and to provide a removable center insert for adding ingredients or measuring. Restores a tight, usable blender top for safe operation. What it does:

• Seals the top of the blender jar to prevent splashes and spills during use
• Center insert allows adding ingredients without removing the full lid
• Helps maintain proper blending performance by keeping bowl contents contained
• Reduces mess and improves user control when pouring or blending hot or cold items

• Hand-wash with warm, soapy water before first use; inspect seal and insert for proper fit
• Ensure lid and insert are correctly seated on the jar before operating the blender
• Do not use if cracked or damaged; replace to avoid leaks or unsafe operation
• Follow appliance user manual safety guidelines.

2 included - Front load

This holder is a replacement mounting bracket that secures a small internal component in place to restore proper alignment and support. It helps keep parts stable so the appliance operates as intended. What it does

• Secures and supports an internal component to prevent movement or misalignment
• Replaces cracked, broken, or worn mounting points that allow rattling or improper part position
• Restores stable contact where a loose component causes intermittent operation or noise
• Fits a specific OEM location; use the part number to confirm exact application

• One replacement holder/mounting bracket

• Disconnect power and water before starting any repairs
• Inspect surrounding clips or fasteners and reuse or replace as needed—this part typically snaps or screws into place
• Handle plastic mounting parts gently to avoid cracking during installation