Parts for Roper GL4030VW1: 05 - Bulkhead Parts

Lint chute directs lint and debris from the dryer drum to the lint screen. Replace if cracked, broken, or clogged to maintain proper airflow.

Replacement screw for washers. Used to secure various components including handles, panels, and internal parts. Order if original is missing or stripped.

Mounting nut for washer assemblies. Secures components and panels in place. Replace if stripped, corroded, or missing to restore proper fastening.

Distributes load under drum support fasteners to prevent hardware loosening. Replace if worn, cracked, or causing noise. Confirm fit with your model number.

Replacement mounting screw for securing components and housings in place. Order a new screw if yours is stripped, missing, or damaged during repairs.

Stop dryer downtime in its tracks — install the Whirlpool WP3392519 OEM Thermal Fuse in minutes.

OEM Quality Fast 1–2 Day Shipping* Free Tech Help

Why choose this fuse?

• Guaranteed OEM: built by Whirlpool to Whirlpool specs — no risky aftermarket clones.
• Broad compatibility: works with Whirlpool, Kenmore, Maytag, KitchenAid, Roper & more.
• Quick delivery: over 94 % of APP orders arrive in 2 days or less.

Fixes these common dryer problems

4-step DIY installation (≈10 min)

1. Unplug dryer and remove rear panel.
2. Locate thermal fuse on blower housing.
3. Transfer wires; secure new fuse with ¼-inch nut-driver.
4. Clean the vent & lint path before testing to prevent repeat failure.

*Video tutorial below.

Ready to get heat back?
Click Add to Cart now & enjoy industry-leading 1–2 day delivery on

Foam seal prevents air leaks around the blower housing in your dryer. Replace if worn, compressed, or causing reduced airflow. Confirm fit by model.

Dryer not heating or overheating clothes? A faulty cycling thermostat may be the cause. Regulates heat levels during the drying cycle. Easy DIY fix.

Dryer making loud noise or not heating properly? A damaged blower wheel disrupts airflow. Moderate DIY repair with video guide available.

Dryer not drying or taking too long? A cracked blower housing disrupts airflow. This assembly restores proper venting for efficient drying cycles.

Secures components in place to prevent movement and reduce vibration during operation. Replace if damaged or missing to restore proper alignment and performance.

Replacement screw for washers. Used to secure various components including handles, panels, and internal parts. Order if original is missing or stripped.

Replaces a corroded, cracked, or damaged dryer heater box housing. This protective enclosure secures internal heating components and wiring in place.

L205-40. Dryer

This insulated wire nut secures and electrically connects two or more appliance wires with a twist-on connection to help maintain a reliable circuit and reduce the risk of loose conductors or shorting. What it does:

• Joins and secures stranded or solid wires for power and control connections
• Creates an insulated, twist-on electrical connection to help prevent shorts
• Helps maintain reliable contact in areas subject to vibration
• Suitable for routine wire splicing and repairs where an OEM wire nut is specified

• Always disconnect power to the appliance before servicing electrical connections
• Strip wire insulation to the appliance manufacturer's recommended length before connecting
• Insert wires fully, then twist the connector until tight and verify a secure mechanical and electrical connection

Replacement 8-18 thread screw for securing panels, brackets, and trim on appliances. Replace worn, stripped, or missing screws to keep components aligned.

Factory protective shield panel for dryer assembly. Guards internal components and directs heat or airflow. Replace if cracked, broken, or missing.

Foam seal pad that cushions the dryer blower housing against the cabinet. Replace if cracked, compressed, or missing to restore proper fit and reduce vibration.

Foam seal pad that cushions the dryer blower housing against the cabinet. Replace if cracked, compressed, or missing to restore proper fit and reduce vibration.

Secures drum support rollers to their shafts in your dryer. Replace if broken, missing, or damaged during roller maintenance to keep drum wheels stable.

Rear drum support roller kit for dryers. Mounts behind the drum to maintain alignment and smooth rotation. Replace when rollers are worn or damaged.

Flat spacer washer that maintains proper spacing between dryer drum components. Replace when worn to reduce friction and prevent metal grinding noises.

Fix dryer drum rattling noise with this lock nut. Secures drum rollers, pulleys, and shafts to prevent loosening from vibration. Simple DIY fix.

Dryer won't heat or flame goes out after ignition? The flame sensor monitors burner flame presence. Common DIY fix with multimeter testing required.

Supports the front drum edge for smooth, quiet rotation. Replace when worn to stop scraping noises or drum wobble. Confirm fit with your model number.

Replacement drum front bulkhead for dryers. Installs at the front of the drum assembly. Needed when original is cracked, damaged, or worn out.

Fix screeching or clanking noises in your dryer. This push clip secures the drum support roller assembly. Moderate DIY repair, requires drum removal.

Seals the lint screen housing to prevent air leaks and maintain proper airflow. Replace if damaged, missing, or causing lint buildup. Verify fit.