Parts for Gibson GER341CS0: 03 - Cabinet / Drum Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This is a small metal grounding ball that sits in the rear drum bearing area of the dryer. It helps dissipate static electricity buildup in the drum during operation. Replace this part if you are experiencing excessive static cling on clothes, static shocks when unloading laundry, or if the original ball is missing or worn.

For a complete drum bearing and shaft kit order 5303281153.

Supports the dryer drum for smooth rotation. Replace if your dryer squeals, makes grinding noises, or the drum sags. Verify fit with your model number.

This metal bracket supports the drum bearing at the rear of the dryer, helping to hold the drum in proper alignment as it rotates. It provides a stable mounting point for the bearing assembly that the drum rides on. Replace this bracket if the dryer makes squealing, grinding, or thumping noises during operation, or if the drum wobbles and does not spin smoothly.

Replacement bracket screw for securing internal panels and brackets to your appliance frame. Needed when original screws are stripped, corroded, or missing.

Fix a dryer that won't heat or takes too long to dry clothes. This heating element assembly generates warm air to dry your laundry efficiently.

Metal heat deflector that mounts near the dryer heating element. Replace if warped, cracked, or damaged to restore proper heat distribution and protect wiring.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

Front bulkhead drum assembly for dryers. Replaces cracked, damaged, or worn drum fronts that cause clothes to snag or tear during drying cycles.

Supports the front of the dryer drum for smooth, quiet rotation. Replace if you hear scraping noise or see wear marks. Verify fit with your model number.

Replacement screw that secures panels and components in dryers, washers, and ranges. Needed when original fasteners are missing, stripped, or worn.

Interior drum baffle that lifts and tumbles clothes during the drying cycle. Replace if cracked, broken, melted, or missing to restore proper tumbling.

Supports the rear of your dryer drum for smooth, even rotation. Replace if drum wobbles, makes noise, or doesn't turn properly. Verify fit by model number.

Dryer won't heat or shows E64 error? High-limit thermostat cuts power if overheating occurs. Moderate DIY fix with our video guide and instructions.

This is a replacement mounting screw used to secure appliance panels, brackets, and components. Replacing worn or missing screws restores proper fit and reduces rattles or loose parts for safe, stable operation. What it does:

• Secures panels, brackets, trim, or small components in place
• Helps eliminate rattling, vibration, and loose or misaligned parts
• Restores proper fastening after maintenance or part replacement
• Matches the appliance's original fastener style for correct fit

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread or component damage

Dryer won't start or shuts off unexpectedly? A failed thermal limiter is often the cause. This safety fuse prevents overheating. DIY repair in 30-45 minutes.

Hex washer head ,10-32 x 0.375. Ground

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

Ceramic dryer heating element housing insulator.

Ceramic dryer heating element terminal block.

Dryer won't start or smells like burning? A melted or loose terminal block where the power cord connects is often the cause. Easy 20-minute repair.

The High Temp Lubricant Tube is an OEM part for Frigidaire appliances, specifically designed to withstand and operate under high temperature conditions. This lubricant is essential for the proper maintenance and functionality of various Frigidaire appliances, offering protection against heat and friction. 

Over time, the lubricant can degrade or become contaminated, which can compromise its effectiveness. Causes of a bad high temp lubricant include exposure to extreme temperatures, accumulation of dirt and debris, or simply the natural breakdown of the lubricant over prolonged use.

Symptoms of needing a new High Temp Lubricant Tube include:

• Increased noise during appliance operation
• Reduced efficiency or performance of the appliance
• Harder movement of parts that should glide smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Supports and allows smooth drum rotation in your dryer. Replace if you hear squealing, grinding, or rattling noises during operation. Verify fit with your model.