Chainsaw Cap, Lid & Cover

This is a standard fuel cap for a hedge trimmer, chainsaw, or weed eater. The fuel cap assembly goes into the tank then screws onto the top of the fuel tank. A fuel cap keeps dirt and debris from falling into the fuel tank and gunking up the engine, causing it to misfire or corrode. Fuel cap assemblies are made of plastic, so they can dry out and snap. If the rubber seal on the fuel cap assembly is no longer preventing fuel from leaking, it’s time to replace it. Installing a new fuel cap assembly is simple. Just push the stopper in and screw on the lid. This is a genuine OEM product shipped from Husqvarna, the manufacturer of this part. This part is also compatible with Craftsman and Poulan products. Part sold individually.

Replacement fuel tank cap assembly for gas blowers and trimmers. Includes retainer connection. Replace if your cap is cracked, won't seal properly, or missing.

Protective gear cap for riding mowers and lawn tractors. Shields internal gears from debris and damage. Replace if cracked, broken, or missing.

Replacement fuel cap assembly for riding mowers and tractors. Seals the fuel tank to prevent leaks and contamination. Order when original cap is cracked or missing.

Protective cover that shields the air filter from damage on chainsaws. Replace if cracked, broken, or missing to keep debris out of the filter housing.

This genuine Husqvarna oil cap can be used as a replacement part for string trimmers, chainsaws, pole pruners, and pole saws. An oil cap in a small engine appliance provides a shield between the fuel line and the exterior of the appliance such that dirt, debris, pebbles, or other external materials cannot enter into the fuel line and such that fuel cannot leak out of the appliance.If an oil cap shows visible signs of damage, it should be removed and replaced immediately with this genuine OEM replacement part. Remember to wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This oil cap is compatible with the following brands: Husqvarna, Poulan, and Weed Eater.

Protective cover plate for chainsaw guide bar assembly. Replaces cracked, damaged, or missing bar plates. Installs on bar mounting area. Direct fit.

Fuel cap assembly for riding mower tractors. Seals the fuel tank to prevent leaks and evaporation. Replace if cracked, damaged, or missing seal.

Protective cover that bolts to the engine housing and encloses the clutch mechanism. Replace if cracked, broken, or missing to protect internal components.

Replacement fuel cap assembly for gas chainsaws. Installs on fuel tank opening. Replace if cap is cracked, threads are stripped, or seal is worn and leaking.

Replacement fuel tank cap assembly for chainsaws. Includes retainer to prevent dropping and contamination. Replaces cracked, broken, or missing caps.

Replacement engine guard for riding mowers. Shields engine from debris and materials. Replace if cracked, broken, or damaged to maintain protection.

This chainsaw throttle wire cap acts as a protective covering for the throttle wire component. The throttle wire is a part that connects the chainsaw trigger with the carburetor so the engine can accelerate. When the chainsaw trigger is squeezed, the carburetor vent opens to allow fuel into the chamber. The more the part is squeezed, the faster the engine goes. The throttle wire cap can become damaged if the chainsaw is damaged through a drop or impact.To replace the throttle wire cap, close the choke lever and unscrew the cover on the air filter. Unscrew the nuts to remove the air filter and remove the throttle rod from the carburetor. Unscrew the screw on the bottom of the handle and lift it away from the trigger. Move the lever to run and lift the interlock lever. Pull the throttle wire out of the cap to remove it. The new part can be installed with the throttle wire.The throttle wire cap is made to be compatible with Husqvarna, Craftsman, Poulan, and Weed Eater chainsaws. It is priced on an individual basis. The part is an authentic OEM replacement component directly obtained from the manufacturer.

This is a rubber or flexible boot that fits over the steering lever to protect the internal mechanism from dirt, moisture, and debris. It helps ensure smooth steering operation by keeping contaminants out of the pivot area. Replace this boot if it is torn, cracked, or deteriorated, which can allow water and grime to enter and cause stiff or unresponsive steering.

This is a genuine breather cover replacement for select outdoor lawn and garden equipment engines. The breather cover, also known as a vent cover, is installed directly onto the vent tube that connects to the carburetor, ensuring that the unit can breathe while it is in use. The vent cover is a sturdy piece, but it is also exposed to a lot of vibrations and could even be affected by impact damage. Replacing it with an original part is going to ensure that your engine can vent correctly. This OEM breather cover is manufactured by Echo. It works with blowers, vacuums, trimmers, edgers, and vent-piped saws from Echo, Little Wonder, and Shindaiwa. The breather cover doesn't require any tools to install. Be sure that gloves are worn whenever doing engine work. Allow the machine to cool completely and work in a well-ventilated area at all times. Make sure that the new vent is installed properly so that the correct engine pressure is maintained and the carburetor can breathe like it should.