Parts for Kenmore Elite 79681073311: Control Panel & Plate Parts

This water tank assembly collects condensation produced during the drying cycle in a ventless or condenser dryer. It is a removable reservoir that must be emptied periodically to allow the dryer to continue operating. Replace this tank if it is cracked, leaking, or if the dryer displays a full tank error even after emptying.

This tub assembly is the main water-containing drum for front-load washers. It replaces a cracked, warped, or damaged tub to stop leaks and restore proper drum rotation and wash performance. What it does:

• Houses the inner drum and contains wash water during cycles
• Supports drum rotation and helps maintain proper agitation/balance
• Stops leaks caused by cracked or warped tubs
• Helps reduce unusual noises or vibration linked to a damaged tub

• Disconnect power and water supply before starting work
• This is a heavy, bulky part — two people are often needed to move and position it safely
• Replace associated seals, gaskets, and fasteners if damaged or worn
• Follow OEM disassembly/reassembly instructions and torque specs; inspect mountings and bearings during install

Dryer control panel assembly fixes unresponsive buttons, blank displays, and cycle selection issues. Moderate DIY repair taking 30-45 minutes.

Fix a dryer that won't heat or leaves clothes damp with this heating element assembly. Generates heat to dry clothes effectively. DIY repair.

Fix a dryer that won't start, stops mid-cycle, or shows error codes with this control board assembly. Moderate difficulty repair requiring basic tools.

This Lifter is a replacement shelf support that helps hold and level adjustable refrigerator shelves for smooth raising and lowering. Restores secure shelf positioning so items stay stable and shelves operate correctly. What it does:

• Supports and stabilizes an adjustable refrigerator shelf, preventing sagging.
• Enables smooth lifting and lowering of the shelf when adjusting positions.
• Replaces cracked, broken, or worn plastic support that lets shelves tilt or fall.
• Helps restore proper alignment so refrigerated items sit level.

• One lifter/shelf support.

• Disconnect power to the appliance before starting any repairs.
• Remove the shelf or bin that sits on the lifter to gain access.
• Snap the lifter into the designated mounting slot; some models may require a light push or a screwdriver to assist.

Fix a dryer that won't start, heat, or complete cycles with this main control board. Controls motor, heating element, and sensors for all dry cycles.

This dryer drum belt wraps around the drum and pulleys to spin clothes. Replace if stretched, cracked, or broken to restore tumbling. Confirm fit by model.

The Hi Limit Thermal Fuse is an OEM part for LG dryers. This fuse is a safety device that protects the dryer from overheating by cutting off power to the heating element if the dryer’s temperature exceeds a safe limit. It ensures that the dryer operates within safe temperature ranges, preventing potential fire hazards.

Replace the hi limit thermal fuse if it becomes faulty due to wear and tear, a buildup of lint, or exposure to high temperatures over time. A malfunctioning fuse can compromise the dryer’s ability to regulate heat properly.

Symptoms of a bad hi limit thermal fuse include:

• The dryer not heating
• The dryer shutting off unexpectedly during a cycle
• No response from the dryer when attempting to start a cycle
• Extended drying times due to lack of heat

This OEM LG part is also compatible with Sears/Kenmore models.

Dryer drum seal creates an airtight barrier between the rotating drum and housing to maintain drying efficiency. Replace if cracked or hardened. Verify fit with your model number.

The Hi Limit Thermostat Assembly is an OEM part for LG dryers. This thermostat monitors and regulates the temperature within the dryer to prevent overheating, ensuring safe and efficient operation. It acts as a safety device that shuts off the heating element if the dryer exceeds a certain temperature, protecting the appliance and your home from potential fire hazards.

Over time, the hi limit thermostat can fail due to wear and tear, electrical issues, or repeated exposure to high temperatures. If the thermostat becomes faulty, it can lead to improper temperature regulation within the dryer.

Symptoms of a bad hi limit thermostat include:

• The dryer overheating
• The dryer not heating at all
• The dryer shutting off mid-cycle
• Extended drying times due to inconsistent heating

This OEM LG part is also compatible with Sears/Kenmore models.

Thread-forming fastener that secures panels, brackets, and internal components. Replace this screw if it's missing, stripped, or damaged during repairs.

This dryer guide cover cap installs on the drum or guide assembly. Replace if your original cover is cracked, broken, missing, or worn from regular use.

Front drum section for your dryer. Installs as the front portion of the drum assembly. Replace if cracked, damaged, or worn from extended use.

Upper mounting plate for dryer assembly. Replaces cracked, broken, or missing plates. Essential structural component for secure installation and support.

This is the start button assembly that initiates the dryer cycle when pressed. It connects to the control panel and engages the dryer's motor circuit. Replace this button if it is stuck, broken, feels loose when pressed, or the dryer does not start when you push it.

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

LED light illuminates your dryer drum for easy viewing during operation. Replace when light dims, flickers, or burns out. Verify fit with your model.

Replace your dryer's duct assembly if cracked, broken, or damaged. This component channels air from the drum through the heating system to ensure proper airflow.

The Roller Kit is an OEM part for LG dryers. This 4 roller kit includes replacement drum support rollers, which are essential for allowing the dryer drum to rotate smoothly during operation. The rollers are designed to provide stable support for the drum, minimizing noise and ensuring efficient drying performance. 

Over time, drum rollers can wear out due to continuous use, exposure to heavy loads, or lack of proper lubrication. When the rollers become damaged or worn, they may develop flat spots, lose their smooth surface, or begin to squeak. These issues can lead to improper drum rotation or increased strain on other dryer components.

Symptoms of a bad Roller Kit include:  

• Loud squeaking, rumbling, or thumping noises during operation  
• The dryer drum not spinning or rotating unevenly  
• Excessive vibrations while the dryer is running  

This OEM LG part is also compatible with Sears/Kenmore.

This is an authentic OEM drum support roller sourced directly from the manufacturer for use in clothes dryers. During the drying cycle, the drum turns and tosses the clothes around to distribute heat. This drum support roller holds the drum in place as it rotates. Over time, the heat from the dryer can lead to the roller becoming worn. If the dryer is making squealing sounds or thumping when operating, the support roller is worn out and should be replaced. Before replacing the drum support roller, make sure the power is disconnected from the dryer. Remove the top and front panel of the dryer to reach the drum. The idler pulley and dryer belt are underneath the drum; remove these and then take the drum out of the unit and set it aside. Remove the mounting bracket holding the worn drum support roller. Remove and replace the worn roller. While the dryer is apart, inspect the remaining support rollers. Reverse the steps used and put the dryer back together. Power the dryer and make sure the drum turns.This is a black and white, rubber and metal part that is individually sold. It does not come with assembly hardware. This drum support roller is designed for dryers manufactured by LG, Kenmore, and General Electric.

A manufacturer-configured replacement component designed to restore the appliance's original factory settings and functions. Use this part when a model-specific, pre-configured module is required to return correct operation. What it does:

• Provides the factory-specific configuration and setup programmed by the manufacturer
• Restores functions controlled by the module when configuration or programming is corrupted
• Resolves symptoms such as appliance not starting, control panel unresponsive, or intermittent/erratic operation linked to configuration errors
• Ensures compatibility with model-specific features when the appliance requires a pre-configured assembly

• Disconnect power to the appliance before starting any work
• Handle electronics carefully; observe electrostatic discharge (ESD) precautions for circuit boards or modules
• Match connectors and mounting locations to the original part; do not force connectors

This hinge bracket is a direct-fit replacement that secures a refrigerator door hinge to the cabinet, restoring proper door alignment and stable operation for safe, reliable use. What it does:

• Secures the door hinge to the cabinet and provides a mounting point for the hinge pin
• Supports the door weight to help maintain correct alignment and door seal
• Helps prevent door sag, uneven gaps, and rubbing during opening/closing
• Can reduce hinge noise or binding caused by a worn or damaged bracket

• Disconnect power and empty or support the door before starting; doors can be heavy and may shift during repair
• Keep original fasteners unless replacement hardware is specified by the manufacturer
• Tighten mounting screws evenly and check door alignment and gasket seal after installation
• Replace worn hinge pin or related parts at the same time for best results

Taptite screw secures dryer panels, brackets, and covers to sheet metal or plastic. Replace if missing, stripped, or damaged during repairs.

Captures lint and debris during drying cycles. Replace when torn, cracked, or difficult to remove. Confirm fit using your dryer's model number.

Replace your dryer's guide cover trim piece if cracked, broken, or missing. This trim protects the guide area and prevents debris from entering the mechanism.

Dryer stops mid-cycle or won't start? This door latch assembly secures the door to keep your dryer running. Simple 2-minute DIY fix for most models.

Replace missing or stripped taptite screws that secure panels and internal components. This thread-forming screw creates a tight hold to eliminate rattles.

This filter guide secures and positions the refrigerator water filter for proper alignment and a reliable seal. It helps keep the filter stable during normal use so water flows correctly and filtration works as intended. What it does:

• Holds the water filter in the correct position inside the filter housing
• Helps maintain a proper seal to reduce the chance of leaks or bypassed water
• Prevents filter movement or rattling when the refrigerator door is opened
• Supports easy removal and replacement of the filter by guiding insertion

• One filter guide

• Designed to install in the refrigerator filter compartment; follow your model's service instructions
• Turn off water supply and relieve system pressure before removing or installing filter components
• Use basic hand tools as required; avoid overtightening which can damage plastic parts
• Inspect surrounding housing and O-rings for wear and replace if needed

This is a safety switch assembly that detects whether the dryer door is open or closed. It signals the control board to stop the drum and heating element when the door is opened during a cycle. Replace this switch if the dryer will not start, stops mid-cycle unexpectedly, or continues running with the door open.

Dryer lint filter cover that secures and protects your lint screen. Replace if cracked, broken, or loose to maintain proper airflow and drying efficiency.

Distortion spring that applies tension within the dryer mechanism. Replace if fatigued, broken, or missing to restore proper tension and assembly function.

Snap-in hole cap covers unused openings on your dryer cabinet or control panel. Replace cracked, broken, or missing caps to restore a finished look.

Single wire harness for dryers. Connects electrical components inside the dryer cabinet. Replace if wires are damaged, frayed, or connectors are broken.

Complete dryer door assembly for front-loading models. Replaces cracked, damaged, or broken door units. Includes outer panel and inner components.

Dryer door won't stay closed or pops open during cycle? This latch hook secures the door panel to prevent rattling and interruptions. Easy 10-minute fix.

Directs steam spray into the dryer drum during Steam/Refresh cycles. Replace if nozzle is clogged, cracked, or leaking to restore proper mist distribution.

Precision mounting screw for dryers and laundry centers. Replaces missing, stripped, or damaged screws that secure panels, brackets, and assemblies. Restores stability.

This outer door frame replaces the visible trim on the front of the microwave door to restore appearance and proper door alignment. It provides a finished look and helps protect the inner door assembly from damage. What it does:

• Replaces damaged, dented, or scratched outer trim for a clean, factory appearance
• Helps secure the door assembly and maintain proper door fit and seal
• Reduces light gaps and vibration caused by warped or loose outer frame
• Matches factory fit and mounting points for straightforward replacement

• One outer door frame as shown

• Use basic hand tools; support the door while removing and reinstalling to avoid dropping
• Disconnect power to the appliance before starting work
• Keep original screws and clips; replace any damaged fasteners with equivalent OEM parts
• If the inner door or latch is damaged, inspect those components and replace as needed

Seals your dryer door to prevent heat loss and improve drying efficiency. Replace if torn, cracked, or causing air leaks. Confirm fit with your model number.

This small damper mounts near the dryer door hinge and cushions the door's movement to prevent it from slamming or bouncing when opened or closed. It absorbs impact and reduces stress on the hinge mechanism. Replace this part if the dryer door slams shut forcefully, swings freely without resistance, or if the existing damper is cracked or missing.

Sound dampening insulation that reduces dryer noise and vibration. Replace if worn, torn, or missing to restore quiet operation and cushioning.

Fix a dryer that won't produce steam or has weak steam output. This steam generator assembly heats water to create steam for steam-enabled cycles.

The DC pump motor assembly powers the pump that moves water through your appliance. Replacing a worn motor helps restore proper water flow so cycles can complete and reduces issues like standing water and excessive noise.

• Drives the pump impeller to move water for draining or circulation, as designed by the appliance
• Supports proper cycle completion by clearing water from the tub or sump
• Common symptoms of a failing motor include standing water, incomplete draining/circulation, loud humming or grinding near the pump, or cycle errors
• May run intermittently, stall, or overheat as internal components wear

• Disconnect power and turn off the water supply before servicing
• Expect residual water; protect the area with towels or a shallow pan
• Note wiring connectors and hose routing; transfer any brackets, grommets, or seals from the original as needed
• Secure hose clamps and test for leaks while running a brief test cycle

This is a flexible hose that connects the condensate drain pump to the water drainage system in a condensing dryer. It carries collected moisture from the pump to the drain outlet or reservoir. Replace this hose if you notice water leaking beneath or behind the dryer, or if the pump is running but water is not being properly drained.

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

Fix loud banging, grinding noise, or poor drying performance with a new dryer blower wheel. Restores proper airflow through drum and exhaust vent.

This is a fastener and retainer assembly that secures the blower wheel to the motor shaft inside a dryer. It keeps the blower wheel firmly in place so it can properly circulate hot air through the drum and out the exhaust vent. Replace this assembly if the blower wheel wobbles, makes rattling or squealing noises, or if the retainer nut is stripped or broken, causing poor airflow and longer drying times.

Blower housing assembly for dryer that channels heated air from the drum to the exhaust. Replaces a cracked or damaged housing to restore proper airflow and help the dryer dry more efficiently and quietly. What it does:

• Channels heated air from the drum to the exhaust and supports the blower wheel.
• Restores airflow when a damaged or cracked housing is restricting ventilation.
• Commonly used to address reduced drying performance and longer dry times.
• Can also resolve unusual rattling or grinding noises coming from the lower front of the dryer.

• Disconnect power (and gas, if applicable) before beginning work; wear eye protection and gloves.
• Remove access panels and disconnect vent/ducting per your model's service instructions to reach the blower housing.
• Inspect the blower wheel and surrounding seals/gaskets while the housing is out; replace damaged components as needed.
• Reassemble all panels and venting securely and test the dryer for proper airflow and operation after installation.

Base bracket for dryer installation and structural support. Replace if your original bracket is cracked, broken, bent, or missing to restore proper stability.

If your dryer isn't venting properly or clothes stay damp, a clogged or damaged exhaust duct may be the cause. This assembly restores airflow in 30 minutes.

This guide assembly is a replacement slide guide that helps support and align moving components for smooth operation and reliable engagement. It restores proper tracking and reduces wobble or binding in the mechanism. What it does:

• Provides stable support and alignment for a sliding component to prevent mis-tracking and uneven movement
• Reduces noise, sticking, or binding caused by worn or damaged guides
• Helps maintain proper clearance and engagement of the moving part
• Matches OEM fit and mounting points for direct replacement

• Turn off and unplug the appliance before beginning any repair to avoid electrical shock
• Remove any obstructing panels or components to access the guide
• Inspect mating parts (slides, rails, fasteners) and replace any damaged hardware to ensure correct fit

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock

The Dryer Thermistor is an OEM part for LG dryers, designed to monitor and help regulate the temperature within the dryer by providing feedback to the control board about the temperature inside the drum. This allows the dryer to adjust its heat settings accordingly, preventing overheating and ensuring clothes are dried evenly and safely.

Symptoms of a bad Dryer Thermistor include:

• Clothes not drying properly or taking longer than usual to dry.
• The dryer repeatedly stopping during a cycle.
• Error messages appearing on the dryer's display panel.
• The dryer getting too hot or not heating enough.

Causes of a bad Dryer Thermistor can include a buildup of lint and debris affecting its ability to accurately sense temperature, wear and tear over time, or electrical issues within the dryer's circuitry.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Dryer Blower Thermostat is an OEM replacement part for LG dryers. It plays a role in regulating the operation of the blower motor, which is responsible for circulating hot air throughout the dryer during the drying cycle.

Causes of a bad dryer blower thermostat can include electrical malfunctions, physical damage, or simply wear and tear over time.

Symptoms of a bad dryer blower thermostat include:  

• The dryer not heating up properly or taking longer to dry clothes
• The blower motor failing to turn on or running continuously
• Inconsistent or inadequate airflow during the drying cycle
• Error codes or fault indicators related to the thermostat or blower motor

This OEM LG part is also compatible with Sears/Kenmore models.

Protective cover shields internal wiring and electrical terminals in your dryer. Replace if cracked, broken, or missing to prevent accidental contact.

Safety cover cap for dryers and laundry centers. Protects internal components and covers exposed areas. Replace if cracked, broken, or missing.

The Motor Bracket is an OEM part for LG dryers. This bracket securely holds the dryer motor in place. It maintains proper alignment and spacing of the motor to allow for smooth operation of the tumble cycle.

Causes of a bad motor bracket can include cracks or breaks developed over time from repeated use and vibration, or damage due to impact or improper installation.

Symptoms of a bad motor bracket include:

• Excessive noise or grinding sounds emanating from the motor area
• The dryer not rotating or tumbling clothes properly
• Increased movement or shaking of the motor
• Poor airflow and inefficient drying performance

This OEM LG part is also compatible with some Kenmore models.

Hardware screws and nuts for installing a dryer side vent kit. Replace missing or stripped fasteners when reconfiguring exhaust outlet direction.

This high-quality, OEM replacement part fits LG and Kenmore dryers, ensuring efficient air circulation for optimal drying. Featuring durable construction, this blower motor addresses common issues such as inadequate drying, unusual noises, and overheating.

This clamp secures hoses, tubing or wiring to the appliance frame to help prevent rubbing, vibration and routing issues. It restores a solid attachment point so lines stay in place during normal use. What it does:

• Holds a hose, tubing or wire bundle in place to prevent chafing and abrasion
• Keeps components routed away from moving parts and hot surfaces
• Reduces rattling or vibration caused by loose lines
• Helps maintain safe, reliable connections by preventing strain on fittings

• Disconnect power and shut off water before servicing
• Use basic hand tools; avoid over-tightening which can pinch hoses or wires
• Inspect adjacent hoses/wires for wear and replace if damaged
• Take photos before removal to ensure correct reinstallation

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

Idler pulley maintains tension on the dryer belt. Replace if worn, cracked, or causing belt slippage. Installs between motor and drum support system.

This replacement screw secures appliance components in their proper position. Use it to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded. What it does:

• Fastens brackets, panels, or trim to keep assemblies aligned and secure
• Helps prevent vibration, rattling, and gaps from loose hardware
• Restores proper attachment when a screw is lost, worn, or damaged
• Common symptoms: loose panel/handle, misalignment, rattling, or a missing screw

• Disconnect power; shut off water or gas before service
• Match location to the original; start threads by hand to avoid cross-threading
• Use the correct driver bit; do not overtighten (especially into plastic)
• If the original hole is stripped, repair threads before installing the new screw

Self-tapping screw secures panels, brackets, and components inside your appliance. Replace stripped, corroded, or missing screws to restore secure fit.

This is a flat drying rack designed to sit inside the dryer drum. It provides a stable surface for drying items like shoes, stuffed animals, or delicate garments that should not tumble freely. Replace this rack if it is bent, broken, or has damaged supports that prevent it from sitting level inside the drum.

Factory vent hose assembly for dryers. Installs between drum and exhaust port. Replace when hose is cracked, torn, disconnected, or missing.